Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSINFINITI2006FX35 AWDREPAIR AND DIAGNOSISBODY & FRAMEEXTERIOR BODY PANELSBODY, LOCK & SECURITY SYSTEM
2006 Infiniti FX35 AWD
Body, Lock & Security System
2006 Infiniti FX35 AWDSECTION Body, Lock & Security System
- Precautions
- Preparation
- Squeak And Rattle Trouble Diagnosis
- Hood
- Radiator Core Support
- Front Fender
- Power Door Lock System
- Component Parts and Harness Connector Location
- System Description
- CAN Communication System Description
- CAN Communication Unit
- Schematic/With Intelligent Key
- Wiring Diagram - D/LOCK -/With Intelligent Key
- Schematic/Without Intelligent Key
- Wiring Diagram - D/LOCK -/Without Intelligent Key
- Terminals and Reference Value for BCM
- Terminals and Reference Value for Intelligent Key Unit (With Intelligent Key System)
- Work Flow
- CONSULT-II Function (BCM)
- Trouble Diagnosis Chart by Symptom
- Check BCM Power Supply and Ground Circuit
- Check Door Switch
- Check Key Switch
- Check Door Lock and Unlock Switch
- Check Door Lock Actuator (Driver Side)
- Check Door Lock Actuator (Passenger Side and Rear LH/RH)
- Check Fuel Lid Lock Actuator
- Check Front Door Key Cylinder Switch (Lock)
- Check Front Door Key Cylinder Switch (Unlock)
- Check Select Unlock Relay Circuit
- Remote Keyless Entry System
- Component Parts and Harness Connector Location
- System Description
- CAN Communication System Description
- CAN Communication Unit
- Schematic
- Wiring Diagram - KEYLES -
- Terminals and Reference Value for BCM
- Terminals and Reference Value for IPDM E/R
- CONSULT-II Function (BCM)
- Work Flow
- Trouble Diagnosis Chart by Symptom
- Check Key Fob Battery and Function
- Check ACC Switch
- Check Door Switch
- Check Key Switch
- Check Remote Keyless Entry Receiver
- Check IPDM E/R Operation
- Check Hazard Warning Lamp Function
- Check Horn Function
- Check Headlamp Function
- Check Map Lamp and Ignition Keyhole Illumination Function
- ID Code Entry Procedure
- Removal and Installation of Remote keyless Entry receiver
- Key Fob Battery Replacement
- Intelligent Key System
- Component Parts and Harness Connector Location
- System Description
- CAN Communication System Description
- CAN Communication Unit
- Schematic
- Wiring Diagram - I/KEY -
- Terminals and Reference Value for INTELLIGENT KEY UNIT
- Terminals and Reference Value for Steering Lock unit
- Terminals and Reference Value for BCM
- Terminals and Reference Value for IPDM E/R
- Diagnosis Procedure
- CONSULT-II Functions (INTELLIGENT KEY)
- CONSULT-II Start Procedure
- CONSULT-II Application Items
- List of Operation Related Parts
- Trouble Diagnosis Symptom Chart
- Check CAN Communication System Inspection
- Check Intelligent Key Unit Power Supply and Ground Circuit
- Check Key Switch (Intelligent Key Unit Input)
- Check Key Switch (BCM Input)
- Check Ignition Knob Switch
- Check Door Switch
- Check Unlock Sensor
- Check Door Request Switch
- Check Intelligent Key Warning Buzzer
- Check Outside Key Antenna
- Check Inside Key Antenna
- Check Steering Lock Unit
- Check Stop Lamp Switch
- Check Detention Switch
- Check Select Unlock Relay
- Check Hazard Function
- Check Horn Function
- Check Headlamp Function
- Check IPDM E/R Operation
- Removal and Installation of Intelligent Key Unit
- Intelligent Key Battery Replacement
- Door
- Front Door Lock
- Rear Door Lock
- Back Door
- Back Door Lock Assembly
- Back Door Auto Closure System
- Component Parts and Harness Connector Location
- System Description
- Wiring Diagram - B/CLOS -
- Terminals and Reference Value for Back Door Closure Control Unit
- Work Flow
- Preliminary Check
- Trouble Diagnosis Chart by Symptom
- Check Back Door Closure Control Unit Power Supply and Ground Circuit
- Check Half-Latch Switch
- Check Close Switch
- Check Open Switch
- Check Back Door Opener Switch (With Intelligent Key)
- Check Back Door Opener Switch (Without Intelligent Key)
- Check Unlock Sensor (Without Intelligent Key)
- Check Closure Motor
- Removal and Installation of Back Door Closer Control Unit
- Vehicle Security (Theft Warning) System
- Component Parts and Harness Connector Location
- System Description
- CAN Communication System Description
- CAN Communication Unit
- Schematic
- Wiring Diagram - VEHSEC -
- Terminals and Reference Value for BCM
- Terminals and Reference Value for IPDM E/R
- CONSULT-II Function (BCM)
- Trouble Diagnosis
- Preliminary Check
- Trouble Diagnosis Symptom Chart
- Diagnostic Procedure 1
- Diagnostic Procedure 2
- Diagnostic Procedure 3
- Diagnostic Procedure 4
- Diagnostic Procedure 5
- Diagnostic Procedure 6
- IVIS (INFINITI Vehicle Immobilizer System-NATS)
- Component Parts and Harness Connector Location
- System Description
- Condition of Security Indicator
- System Composition
- ECM Re-Communicating Function
- Wiring Diagram - NATS -
- Terminals and Reference Value for Steering Lock Unit/with Intelligent Key System
- Terminals and Reference Value for Intelligent Key Unit/with Intelligent Key System
- Terminals and Reference Value for BCM
- Consult-II
- Diagnosis Procedure
- Trouble Diagnosis Symptom Chart
- Security Indicator Inspection
- Diagnostic Procedure 1
- Diagnostic Procedure 2
- Diagnostic Procedure 3
- Diagnostic Procedure 4
- Diagnostic Procedure 5
- Diagnostic Procedure 6
- Diagnostic Procedure 7
- Removal and Installation NATS Antenna Amp.
- Integrated HOMELINK Transmitter
- Body Repair
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.