Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Check Outside Key Antenna
- CHECK OUTSIDE KEY ANTENNA POWER SUPPLY
Push each door request switch, and use an oscilloscope to check voltage waveform of harness between Intelligent Key unit connector M34 terminals 17 (back door), 19 (driver and rear LH door), and 37 (passenger and rear RH door) and ground.
VOLTAGE SPECIFICATIONSTerminal (Wire color) Condition Signal (Reference value) (+) (-) Back door: 17 (L) Ground Push each door request switch Driver, rear LH: 19 (SB) Passenger, rear RH 37 (G) OK or NG
OK : GO TO 2.
NG : GO TO 3.
- CHECK OUTSIDE KEY ANTENNA OPERATION
- Disconnect each outside key antenna connector.
- Check the following.
- Check continuity between door mirror (outside key antenna) connector D2 (driver side), D32 (passenger side) terminals 14 and 15
- Check continuity between outside key antenna D62 (rear door LH), D82 (rear door RH), D116 (back door) terminals 1 and 2
Driver side, Passenger side
14 - 15 : Continuity should exist.
Back door, Rear door
1 - 2 : Continuity should exist.
OK or NG
OK : GO TO 3.
NG : Replace outside key antenna.
- CHECK OUTSIDE KEY ANTENNA CIRCUIT
- Disconnect Intelligent Key unit connector.
- Check continuity between each outside key antenna connector D2 (driver side), D32 (passenger side), D62 (rear door LH), D82 (rear door RH), D116 (back door) terminals 1, 2, 14, 15 and Intelligent Key unit connector M34 terminals 17, 18, 19, 20, 37, and 38.CONTINUITY SPECIFICATIONS
Item Terminal (Wire color) Continuity Back door 1 (L/B) 17 (L) Yes 2 (W/B) 18 (W/L) Driver side 14 (BR/W) 19 (SB) 15 (R/Y) 20 (GY) Passenger side 14 (G/Y) 37 (G) 15 (L/Y) 38 (G/W) Rear door LH 1 (G/Y) 19 (SB) 2 (PU/W) 20 (GY) Rear door RH 1 (G/Y) 37 (G) 2 (PU/W) 38 (G/W) - Check continuity between each out side key antenna connector terminals 1, 2, 6, 7 and ground.CONTINUITY SPECIFICATIONS
Item Terminal (Wire color) Continuity Back door 1 (L/B) Ground No 2 (W/B) Rear door (LH, RH) 1 (G/Y) 2 (PU/W) Driver side 14 (BR/W) 15 (R/Y) Passenger side 14 (G/Y) 15 (L/Y)
OK or NG
OK : Replace Intelligent Key unit.
NG : Replace harness between outside key antenna and Intelligent Key unit.
NO RELATED
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.