Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHRYSLER1993LEBARON LANDAUREPAIR AND DIAGNOSISBRAKESTRACTION CONTROLANTI-LOCK BRAKE SYSTEM - BENDIX-6
1993 Chrysler LeBaron Landau
Anti-Lock Brake System - BENDIX-6
1993 Chrysler LeBaron LandauSECTION Anti-Lock Brake System - BENDIX-6
- Identification
- Description
- Operation
- Bleeding Brake System
- Diagnosis & Testing
- Connector Identification
- Self-Diagnostic Tests
- Notes
- Test 1A Reading Fault Messages
- Test 2A Testing Blank DRB-II Message Screen
- Test 3A Testing DRB-II No Response Message
- Test 4A Antilock Lamp Fault
- Test 4B Antilock Lamp Fault
- Test 5A Antilock Lamp Relay Fault
- Test 5B Antilock Lamp Relay Fault
- Test 6A Cab Fault
- Test 7A Excess Decay Fault
- Test 8A Left Front Wheel Speed Sensor Continuity Fault
- Test 9A Left Front Wheel Speed Sensor Fault
- Test 10A Left Rear Wheel Speed Sensor Continuity Fault
- Test 11A Left Rear Wheel Speed Sensor Fault
- Test 12A Modulator Fault
- Test 12B Modulator Fault (Left Front Build/Decay Valve)
- Test 12C Modulator Fault (Left Rear Build/Decay Valve)
- Test 12D Modulator Fault (Right Front Build/Decay Valve)
- Test 12E Modulator Fault (Right Rear Build/Decay Valve)
- Test 12F Modulator Fault (LF/RR Isolation Valve)
- Test 12G Modulator Fault (RF/LR Isolation Valve)
- Test 12H Modulator Fault (Solenoid Valve)
- Test 13A Stop Lamp Switch Input Test
- Test 14A Pump/Motor Fault
- Test 14B Pump/Motor Fault
- Test 14C Pump/Motor Fault
- Test 14D Pump/Motor Fault
- Test 15A Red Brake Warning Lamp Input Test
- Test 15B Red Brake Warning Lamp Input Test
- Test 16A Right Front Wheel Speed Sensor Continuity Fault
- Test 17A Right Front Wheel Speed Sensor Fault
- Test 18A Right Rear Wheel Speed Sensor Continuity Fault
- Test 19A Right Rear Wheel Speed Sensor Fault
- Test 20A Solenoid UNDERVOLTAGE Fault
- Test 20B Solenoid UNDERVOLTAGE Fault
- Test 20C Solenoid UNDERVOLTAGE Fault
- Test 20D Solenoid UNDERVOLTAGE Fault
- Test 21A System Relay Fault
- Test 21B System Relay Fault
- VER-1A - Verification Procedure
- Removal & Installation
- Adjustments
- Torque Specifications
- Wiring Diagrams
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.