Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSAUDI1996A4 BASE, STANDARDREPAIR AND DIAGNOSISQUICK LOOKUPSTECHNICAL BULLETINSTECHNICAL SERVICE BULLETINSOTHER VARIANT
1996 Audi A4 Base, Standard
Technical Service Bulletins: Other Variant
1996 Audi A4 Base, StandardSECTION Other Variant
WARNING: This page is about the A4 Base, Automatic, which is a different variant/trim than selected.
- A/C Compressor
- Accessories Control Systems
- Accessory Drive Belts
- Air Bag, SRS
- Airbag Or Pyrotechnic Safety Belt Deployment, Inquiries (GROUP 69, NO. 97-03)
- Airbag, Replacement Interval Change (GROUP 69, NO. 08-04)
- Deployed Airbag, Repair Warning! (GROUP 69, NO. 02-01)
- Disassembling Suspension Strut - Tool Correction (GROUP 42, NO. 96-01)
- Air Bag V - VAG 1551 Scan Tool Communication (GROUP 69, NO. 96-01)
- Drivers Side Airbag, Removal Tool Change (GROUP 69, NO. 95-05)
- Anti-Lock Brakes
- Abs Activates During Light Brake Application (GROUP 45, NO. 08-04)
- Abs Light (K47) On Due To Battery Jumping/Charging (GROUP 01, NO. 97-01)
- Abs Hydraulic Unit Removing & Installing (GROUP 45, NO. 96-01)
- Disassembling Suspension Strut - Tool Correction (GROUP 42, NO. 96-01)
- EDL With Suction-Regulated Control - Changes To OBD (GROUP 01, NO. 96-05)
- Anti-Theft Systems
- Door Components & Seals - Removing & Installing (GROUP 57, NO. 97-04)
- Rear Lid Buffer Stop Adjusting (GROUP 55, NO. 97-02)
- Replacement Key - Key Code No Longer On Vehicle (GROUP 57, NO. 96-02)
- Ignition/Trunk Lock Cylinder Replacement (GROUP 57, NO. 96-01)
- Rear Ashtray Lid Binds - New Rubber Tabs Metal Strip (GROUP 68, NO. 95-01)
- Automatic Trans
- Fluid Capacity Chart (GROUP 00, NO. 98-01)
- Delayed 1-2 Shift On Cold Start Warm-Up (GROUP 37, NO. 98-01)
- New Lifetime Coolant For All Aluminum Engines (GROUP 19, NO. 96-01)
- Maintenance/Lubrication Schedule Change (A96-01)
- Trans. Oil Seals, Lubrication Prior To Installation (GROUP 34, NO. 96-01)
- Trans. Oil Seals, Lubrication Prior To Installation (GROUP 39, NO. 96-02)
- Auxiliary Emission Control Systems
- All Models - Tip For Replacing A Control Module (CTT 00-14-03)
- All Models, 02 Sensor DTCS (CTT 01-14-01)
- All Vehicles - Software Updating Tips (CTT 01-14-02)
- Leak Detection Pump (LDP) -V144-, Quick Check (GROUP 20, NO. 08-10)
- Verifying Post Oxygen Sensor Connection After Repair (GROUP 01, NO. 00-03)
- 2.8 V6 5V - Repair Manual Updates/Revisions (GROUP 28, NO. 98-01)
- 2.8 V6 5V - Repair Manual Updates/Revisions (GROUP 24, NO. 98-01)
- 1.8T - Diagnostic Trouble Code (DTC) Table Additions (GROUP 01, NO. 97-14)
- J 1930 Nomenclature Revisions (GROUP 00, NO. 96-03)
- Knock Sensor Terminal Number Correction (MMS410) (GROUP 28, NO. 96-03)
- Replacement For Defective USA/CDN/6 Program Card (A96-03)
- Multiple Diagnostic Trouble Codes Stored (GROUP 01, NO. 96-02)
- Trouble Codes After Driving With Low Fuel Level (GROUP 01, NO. 95-11)
- OBD II General Diagnostic Worksheet (GROUP 01, NO. 95-10)
- Axle Shafts
- Body Interior
- Brakes Control Systems
- All Models - Tip For Replacing A Control Module (CTT 00-14-03)
- All Vehicles - Software Updating Tips (CTT 01-14-02)
- Abs Activates During Light Brake Application (GROUP 45, NO. 08-04)
- Abs Light (K47) On Due To Battery Jumping/Charging (GROUP 01, NO. 97-01)
- Abs Hydraulic Unit Removing & Installing (GROUP 45, NO. 96-01)
- EDL With Suction-Regulated Control - Changes To OBD (GROUP 01, NO. 96-05)
- Charging Systems
- Clutch
- Collision/Avoidance
- Communication Devices
- Component Locations
- Cooling System (Mechanical)
- 19 Identifying And Mixing Factory Fill Engine Coolants (GROUP 19, NO. 23-36)
- 2.8 V6 5V - Repair Manual Updates/Revisions (GROUP 01, NO. 98-02)
- Engine Oil Seals, Lubrication Prior To Installation (GROUP 13, NO. 96-02)
- New Lifetime Coolant For All Aluminum Engines (GROUP 19, NO. 96-01)
- Maintenance/Lubrication Schedule Change (A96-01)
- Engine Oil Seals, Lubrication Prior To Installation (GROUP 15, NO. 96-01)
- Rear Crankshaft Seal Leaking After Replacement (GROUP 13, NO. 95-01)
- Cruise Control Systems
- Differentials & Drive Axles
- Electronic Steering
- Electronic Suspension
- Engine Control Systems
- All Models - Tip For Replacing A Control Module (CTT 00-14-03)
- All Models, 02 Sensor DTCS (CTT 01-14-01)
- All Vehicles - Software Updating Tips (CTT 01-14-02)
- Leak Detection Pump (LDP) -V144-, Quick Check (GROUP 20, NO. 08-10)
- Verifying Post Oxygen Sensor Connection After Repair (GROUP 01, NO. 00-03)
- 2.8 V6 5V - Repair Manual Updates/Revisions (GROUP 28, NO. 98-01)
- 1.8T - Diagnostic Trouble Code (DTC) Table Additions (GROUP 01, NO. 97-14)
- J 1930 Nomenclature Revisions (GROUP 00, NO. 96-03)
- Knock Sensor Terminal Number Correction (MMS410) (GROUP 28, NO. 96-03)
- Replacement For Defective USA/CDN/6 Program Card (A96-03)
- Multiple Diagnostic Trouble Codes Stored (GROUP 01, NO. 96-02)
- Trouble Codes After Driving With Low Fuel Level (GROUP 01, NO. 95-11)
- OBD II General Diagnostic Worksheet (GROUP 01, NO. 95-10)
- Entertainment Systems
- Cigarette Lighter Element Does Not Eject Or Cigarette Lighter Socket INOP (GROUP 90, NO. 13-41)
- GEKO, Radio Code Retrieval Using Vas 5051 (GROUP 91, NO. 08-168)
- Radio, Symphony II, Control Knobs Available As Replacement Parts (GROUP 91, NO. 08-170)
- Use Od Novelty Discs In Compact Disc Player (GROUP 91, NO. 98-03)
- Am Radio - Inaccurate Display (GROUP 91, NO. 96-05)
- Radio Distortion Or Radio Momentarily Fades Out (GROUP 91, NO. 96-03)
- Buzzing Sound From Front Speakers (GROUP 91, NO. 95-10)
- Cd Changer Skipping - Orientation Switch Inspection (GROUP 91, NO. 95-09)
- Radio Volume Goes To Maximum When Adjusted (GROUP 91, NO. 95-08)
- Cd Player Installation Instructions (GROUP 91, NO. 95-05)
- Exhaust
- Exterior Body Panels
- Exterior Lights
- Frames, Subframes & Crossmembers
- Underbody Close-Out Cover, Installing At PDI (GROUP 00, NO. 01-06)
- Underbody Plugs, Eliminating Wind Noise (GROUP 50, NO. 01-01)
- Body Damage When Moving Vehicle By Hand (GROUP 00, NO. 97-02)
- Swing Arm Removing/Installing - SUBFRAME Positioning (GROUP 40, NO. 96-01)
- Front License Plate Bracket Installation (GROUP 66, NO. 95-01)
- Front Suspension
- Front Suspension Noisy (GROUP 40, NO. 01-01)
- Alignment Requirements After Component Removal (GROUP 44, NO. 98-02)
- Front Suspension Noisy (GROUP 40, NO. 98-02)
- Brake Pedal Pulsation/Steering Wheel Shimmy Checking (GROUP 46, NO. 98-01)
- Changes To Front Suspension (GROUP 40, NO. 96-02)
- Changes To Rear Suspension (GROUP 42, NO. 96-02)
- Disassembling Suspension Strut - Tool Correction (GROUP 42, NO. 96-01)
- Swing Arm Removing/Installing - SUBFRAME Positioning (GROUP 40, NO. 96-01)
- Front Strut Shipping Spacers Removing (GROUP 40, NO. 95-02)
- Rear Suspension Retaining Strap (GROUP 42, NO. 95-01)
- Fuel System
- Fuses & Circuit Breakers
- Gauges & Instrument Panels
- Rear Lid Buffer Stop Adjusting (GROUP 55, NO. 97-02)
- Instrument Cluster Bulb Locations (GROUP 90, NO. 96-02)
- Tachometer Sticks/Temp. Reading Changes To CELSIUS (GROUP 90, NO. 96-01)
- Rear Ashtray Lid Binds - New Rubber Tabs Metal Strip (GROUP 68, NO. 95-01)
- Ambient Temperature/Gear Indicator Light Not Visible (GROUP 90, NO. 95-11)
- Tachometer Indicates Higher Than Actual Rpm (GROUP 90, NO. 95-10)
- Fuel Gauge Does Not Register Full (GROUP 90, NO. 95-08)
- DTC P0461/16845 Fuel Filler Level Signal (GROUP 01, NO. 95-08)
- Headlights
- Heated Glass/Defoggers
- HVAC Control Systems
- Identification
- Ignition Switch/Steering Lock
- Ignition System
- Interior/Exterior Trim
- Center Armrest, Eliminating Creaking Noise (GROUP 68, NO. 99-02)
- Floor Mats Missing Logo (GROUP 67, NO. 98-02)
- Door Components & Seals - Removing & Installing (GROUP 57, NO. 97-04)
- Rear Center Armrest Removing & Installing (GROUP 72, NO. 97-02)
- Trim, Carpeting & Center Console Removing/Installing (GROUP 70, NO. 97-02)
- Front/Rear Door Seals - Friction Noise (GROUP 57, NO. 97-02)
- HATSHELF Trim (Beading) Loose (GROUP 70, NO. 95-02)
- Interior/Illumination Lights
- Locking Hubs
- Lubrication System
- Engine Oil Seals, Lubrication Prior To Installation (GROUP 13, NO. 96-02)
- New Lifetime Coolant For All Aluminum Engines (GROUP 19, NO. 96-01)
- Maintenance/Lubrication Schedule Change (A96-01)
- Engine Oil Seals, Lubrication Prior To Installation (GROUP 15, NO. 96-01)
- Rear Crankshaft Seal Leaking After Replacement (GROUP 13, NO. 95-01)
- Manual Steering
- Manual Trans
- Remanufactured Transmission Pre-Filled With Oil (GROUP 34, NO. 98-01)
- Fluid Capacity Chart (GROUP 00, NO. 98-01)
- 012 Manual Trans. - Revisions To Service Procedures (GROUP 34, NO. 97-01)
- 012 Manual Transmission - Technical Data (GROUP 00, NO. 97-13)
- Final Drive Flange/Seal Differential Torque Revision (GROUP 39, NO. 97-01)
- Input Shaft/Pinion Shaft - Revised Operating Sleeve (GROUP 35, NO. 97-01)
- 012 Manual Transmission Revisions (GROUP 34, NO. 96-02)
- Trans. Oil Seals, Lubrication Prior To Installation (GROUP 34, NO. 96-01)
- Mechanical
- All Models, Dynamic Compression Test Using DSO Function (CTT 00-14-01)
- Hydraulic Versus Mechanical TENSIONERS (TT001-13)
- Verifying Post Oxygen Sensor Connection After Repair (GROUP 01, NO. 00-03)
- 1.8L (AEB) - Camshaft Sprocket Torque Specification Change (GROUP 15, NO. 98-02)
- 2.8L V6 (2-Valve) - Toothed Camshaft Drive Belt, Removing And Installing (GROUP 13, NO. 97-01)
- Engine Oil Seals, Lubrication Prior To Installation (GROUP 13, NO. 96-02)
- Pistons/Combustion Chambers/Valves - Carbon Build Up (GROUP 15, NO. 96-02)
- Maintenance/Lubrication Schedule Change (A96-01)
- Engine Oil Seals, Lubrication Prior To Installation (GROUP 15, NO. 96-01)
- Rear Crankshaft Seal Leaking After Replacement (GROUP 13, NO. 95-01)
- Mechanical - Hydraulic
- 44 Tightening Wheel Bolts (GROUP 44, NO. 14-55)
- Brake Pedal Pulsation/Steering Wheel Shimmy Checking (GROUP 46, NO. 98-01)
- Brake Squeal - Component Cleaning/Lubricant (GROUP 46, NO. 97-01)
- New Lifetime Coolant For All Aluminum Engines (GROUP 19, NO. 96-01)
- Front Brake Caliper Service: Bleeding/Changing Fluid (GROUP 47, NO. 96-01)
- Front Brakes Servicing (TEVES Brake Calipers) (GROUP 46, NO. 96-02)
- Front Brake Pads Servicing (GROUP 46, NO. 96-01)
- Memory Modules
- Mirrors
- Overdrive Unit
- Paint & Coatings
- Passive Restraints
- Rear Suspension
- Alignment Requirements After Component Removal (GROUP 44, NO. 98-02)
- Front Suspension Noisy (GROUP 40, NO. 98-02)
- Changes To Rear Suspension (GROUP 42, NO. 96-02)
- Disassembling Suspension Strut - Tool Correction (GROUP 42, NO. 96-01)
- Swing Arm Removing/Installing - SUBFRAME Positioning (GROUP 40, NO. 96-01)
- Front Strut Shipping Spacers Removing (GROUP 40, NO. 95-02)
- Rear Suspension Retaining Strap (GROUP 42, NO. 95-01)
- Restraints Control Systems
- Schedule
- Seats
- Front Seat Backrest Panel Removing & Installing (GROUP 74, NO. 98-01)
- Rear Center Armrest Removing & Installing (GROUP 72, NO. 97-02)
- Rear Lid Buffer Stop Adjusting (GROUP 55, NO. 97-02)
- Rear Three-Point Seat Belts - Removing & Installing (GROUP 68, NO. 97-07)
- Split Rear Seat Backrest Cover Removing & Installing (GROUP 74, NO. 97-01)
- Rear Child Restraint Anchorages (GROUP 69, NO. 97-01)
- Sunroof Loud Clicking Noise When Closing (GROUP 60, NO. 95-01)
- Starter
- Steering Column
- Steering Control Systems
- Steering Gear
- Steering Linkage
- Front Suspension Noisy (GROUP 40, NO. 01-01)
- Front Suspension Noisy (GROUP 40, NO. 98-02)
- Brake Pedal Pulsation/Steering Wheel Shimmy Checking (GROUP 46, NO. 98-01)
- Changes To Front Suspension (GROUP 40, NO. 96-02)
- Wheel Alignment Specifications (GROUP 44, NO. 96-01)
- Disassembling Suspension Strut - Tool Correction (GROUP 42, NO. 96-01)
- Sun Roof/T-Top/Convertible Top
- Suspension Control Systems
- System
- All Models - Tip For Replacing A Control Module (CTT 00-14-03)
- All Models, 02 Sensor DTCS (CTT 01-14-01)
- All Vehicles - Software Updating Tips (CTT 01-14-02)
- Leak Detection Pump (LDP) -V144-, Quick Check (GROUP 20, NO. 08-10)
- Verifying Post Oxygen Sensor Connection After Repair (GROUP 01, NO. 00-03)
- 2.8 V6 5V - Repair Manual Updates/Revisions (GROUP 01, NO. 98-02)
- 2.8 V6 5V - Repair Manual Updates/Revisions (GROUP 28, NO. 98-01)
- 2.8 V6 5V - Repair Manual Updates/Revisions (GROUP 24, NO. 98-01)
- 1.8T - Diagnostic Trouble Code (DTC) Table Additions (GROUP 01, NO. 97-14)
- J 1930 Nomenclature Revisions (GROUP 00, NO. 96-03)
- Engine Oil Seals, Lubrication Prior To Installation (GROUP 13, NO. 96-02)
- Knock Sensor Terminal Number Correction (MMS410) (GROUP 28, NO. 96-03)
- Replacement For Defective USA/CDN/6 Program Card (A96-03)
- Pistons/Combustion Chambers/Valves - Carbon Build Up (GROUP 15, NO. 96-02)
- Multiple Diagnostic Trouble Codes Stored (GROUP 01, NO. 96-02)
- Maintenance/Lubrication Schedule Change (A96-01)
- Engine Oil Seals, Lubrication Prior To Installation (GROUP 15, NO. 96-01)
- Trouble Codes After Driving With Low Fuel Level (GROUP 01, NO. 95-11)
- Rear Crankshaft Seal Leaking After Replacement (GROUP 13, NO. 95-01)
- OBD II General Diagnostic Worksheet (GROUP 01, NO. 95-10)
- Transmission Control Systems
- Vacuum Pumps/Lines/Tanks/Water Trap
- Warning Systems
- Wheel Alignment
- Wheel Hubs
- Wheels & Tire System
- 44 Tightening Wheel Bolts (GROUP 44, NO. 14-55)
- Alloy Wheels, Cleaning (GROUP 44, NO. 99-01)
- Brake Pedal Pulsation/Steering Wheel Shimmy Checking (GROUP 46, NO. 98-01)
- Changes To Front Suspension (GROUP 40, NO. 96-02)
- Changes To Rear Suspension (GROUP 42, NO. 96-02)
- Disassembling Suspension Strut - Tool Correction (GROUP 42, NO. 96-01)
- Window Motors & Regulators
- Wiper/Washer Systems
- Wiring System (Data Link Connectors, Pwr Dist., Grnd Dist.)
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.