Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2019 Mazda 6 Grand TouringFACTORY OEM SERVICE PROCEDURE
Engine Control System (VIN Y)
- Accelerator Pedal Position (App) Sensor Inspection
- Accelerator Pedal Position (App) Sensor Removal/Installation
- Air Fuel Ratio (A/F) Sensor Inspection
- Air Fuel Ratio (A/F) Sensor Removal/Installation
- Barometric Pressure (BARO) Sensor Inspection
- Barometric Pressure (BARO) Sensor Removal/Installation
- Boost Air Temperature Sensor Inspection
- Boost Pressure Sensor Inspection
- Boost Pressure Sensor/Boost Air Temperature Sensor Removal/Installation
- Camshaft Position (CMP) Sensor Inspection
- Camshaft Position (CMP) Sensor Removal/Installation
- Control System Diagram
- Control System Wiring Diagram
- Crankshaft Position (CKP) Sensor Inspection
- Crankshaft Position (CKP) Sensor Removal/Installation
- Engine Control System Location Index
- Engine Coolant Temperature (ECT) Sensor Inspection
- Engine Coolant Temperature (ECT) Sensor Removal/Installation
- Engine Oil Data Reset
- Engine Oil Level Sensor Inspection
- Engine Oil Level Sensor Removal/Installation
- Engine Oil Pressure Sensor Inspection
- Engine Oil Pressure Sensor/Engine Oil Temperature Sensor Removal/Installation
- Engine Oil Temperature Sensor Inspection
- Exhaust Gas Pressure Sensor Inspection
- Exhaust Gas Pressure Sensor Removal/Installation
- Fuel Tank Pressure Sensor Inspection
- Fuel Tank Pressure Sensor Removal/Installation
- Fuel Temperature Sensor Inspection
- Heated Oxygen Sensor (Ho2S) Inspection
- Heated Oxygen Sensor (Ho2S) Removal/Installation
- High Fuel Pressure Sensor Inspection
- High Fuel Pressure Sensor Removal/Installation
- Intake Air Temperature (IAT) Sensor Inspection
- Ion Sensor Inspection
- Ion Sensor Removal/Installation
- Knock Sensor (KS) Inspection
- Knock Sensor (KS) Removal/Installation
- Low Fuel Pressure Sensor Inspection
- Low Fuel Pressure Sensor/Fuel Temperature Sensor Removal/Installation
- Manifold Absolute Pressure (Map) Sensor Inspection
- Manifold Absolute Pressure (Map) Sensor/Intake Air Temperature (IAT) Sensor No. 2 Removal/Installation
- Mass Air Flow (MAF) Sensor Inspection
- Mass Air Flow (MAF) Sensor/Intake Air Temperature (IAT) Sensor No. 1 Removal/Installation
- Pcm Configuration (Using As-Built Data)
- Pcm Configuration (Using Read/Write Function)
- Pcm Inspection
- Without Using The M-MDS
- Inspection Using An Oscilloscope (Reference)
- Drive-By-Wire Control (+) Signal
- Hydraulic Variable Valve Timing Control Signal
- Electric Variable Valve Timing Control Signal
- Electric Variable Valve Timing Motor (Rotation Direction) Signal
- Electric Variable Valve Timing Motor (Rotation Pulse) Signal
- Electric Variable Valve Timing Driver (Diagnostic) Signal
- Fuel Injection Control (+) Signal
- Fuel Injection Control (-) Signal
- Fuel Pump Control Signal
- Fuel Pump Control Module (Diagnostic) Signal
- High Pressure Fuel Pump Control (+) Signal
- High Pressure Fuel Pump Control (-) Signal
- IGT1, IGT2, IGT3, IGT4 Control
- Purge Control
- A/F Sensor Heater Control Signal
- HO2S Heater Control Signal
- Cooling Fan Control Signal
- Generator field Coil Control Signal
- Generator Output Voltage
- Intake CMP Signal
- Exhaust CMP Signal
- CKP Signal
- Wastegate Valve Control (-) Signal
- Using The M-MDS
- Pcm Removal/Installation
- Throttle Position (TP) Sensor Inspection
- Throttle Position (TP) Sensor Removal/Installation
- WASTEGATE Valve Position Sensor Inspection
- WASTEGATE Valve Position Sensor Removal/Installation
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
