Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Kia Rondo BaseFACTORY OEM SERVICE PROCEDURE
Automatic Transaxle System (F4A42)
- General
- Automatic Transaxle System
- Description
- Power Train
- P Position
- N Position
- 1ST Gear Power Flow
- 2ND Gear Power Flow
- 3RD Gear Power Flow
- 4TH Gear Power Flow
- Reverse Gear Power Flow
- Hydraulic Control System
- VFS (Variable Force Solenoid)
- Reducing Pressure
- Hydraulic Pressure Table
- N-P
- D 1ST Gear
- D 2ND Gear
- D 3RD Gear
- D 4TH Gear
- Reverse
- Electronic Control System
- Sports Mode
- Signals Of Sports Mode Switch
- Controller Area Network (Can)
- TCM Pin Description
- TCM Input/Output Signal Voltage Check Sheet
- Service Adjustment Procedure
- Troubleshooting
- Diagnosis Flow
- Inspection Chart For Trouble Symptoms
- DTC Troubleshooting Index
- FAILSAFE
- FAILSAFE According To The DTC
- Service Data List (With Scan Tool)
- HIVEC - Sat (Siemens Adaptive Transmission Control) Mode (Shift Pattern)
- Actuator Inspection
- Road Test
- Torque Converter Stall Test
- Torque Converter Stall Test Conclusion
- Hydraulic Pressure Test
- Standard Hydraulic Pressure Test
- DTC P0703 Brake S/W Malfunction
- DTC P0707 Transaxle Range Switch - Low Input
- DTC P0708 Transaxle Range Switch - High Input
- DTC P0711 Transaxle Fluid Temperature Sensor Rationality
- DTC P0712 Fluid (Oil) Temperature Sensor Circuit - Low
- DTC P0713 Fluid (Oil) Temperature Sensor Circuit - High
- DTC P0717 Input Speed Sensor Circuit - No Signal
- DTC P0721 A/T Output Speed Sensor Circuit - Open Or Short (GND)
- DTC P0722 Output Speed Sensor Circuit - No Signal
- DTC P0731 Gear 1 Incorrect Ratio
- DTC P0732 Gear 2 Incorrect Ratio
- DTC P0733 Gear 3 Incorrect Ratio
- DTC P0734 Gear 4 Incorrect Ratio
- DTC P0741 Torque Converter Clutch Circuit - Stuck Off
- DTC P0743 Torque Converter Clutch Circuit - Electrical
- DTC P0748 Pressure Control Solenoid Valve A - Electrical
- DTC P0750 Shift Control Solenoid Valve A Circuit Malfunction
- DTC P0755 Shift Control Solenoid Valve B Circuit Malfunction
- DTC P0760 Shift Control Solenoid Valve C Circuit Malfunction
- DTC P0765 Shift Control Solenoid Valve D Circuit Malfunction
- DTC P0885 A/T Relay Circuit Malfunction
- DTC U0001 Can Communication Malfunction
- DTC U0100 Can Mi-Com Or Circuit Mal
- Automatic Transaxle
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.