Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMITSUBISHI2007ENDEAVOR SE, FWDREPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSCOMMON SPECS & PROCEDURESSPECIFICATIONS INDEX
2007 Mitsubishi Endeavor SE, FWD
Specifications Index
2007 Mitsubishi Endeavor SE, FWDSECTION Specifications Index
ENDEAVOR SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | |||
| Automatic | GENERAL DESCRIPTION | ||
| Manual | GENERAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 226 +/- 29 N.m (167 +/- 21 ft-lb) | ||
| Rear (AWD) | 226 +/- 29 N.m (167 +/- 21 ft-lb) | ||
| Battery | ON-VEHICLE SERVICE | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING | ||
| Disc Brakes | |||
| Service Specifications | GENERAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drum Brakes (Parking Brake) | |||
| Service Specifications | Refer to GENERAL SPECIFICATIONS . Also refer to SERVICE SPECIFICATIONS . | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS . | ||
| Charging | |||
| Generator | SERVICE SPECIFICATIONS | ||
| Torque | REMOVAL AND INSTALLATION | ||
| Drive Belts | |||
| Adjustment | 7. DRIVE BELTS (FOR GENERATOR, POWER STEERING OIL PUMP AND AIR CONDITIONING) (CHECK CONDITION) | ||
| Belt Routing | 7. DRIVE BELTS (FOR GENERATOR, POWER STEERING OIL PUMP AND AIR CONDITIONING) (CHECK CONDITION) | ||
| Engine Cooling | |||
| General Service Specifications | SERVICE SPECIFICATION | ||
| Radiator Cap Pressure | Standard value: 93 - 123 kPa (14 - 18 psi), Minimum limit: 83 kPa (12 psi) | ||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Mechanical | |||
| Compression | Standard value (at engine speed of 200 r/min): 1,548 kPa (225 psi). Minimum limit (at engine speed of 200 r/min): 1,117 kPa (162 psi). Difference between cylinders: Limit: 98 kPa (14 psi) | ||
| Oil Pressure | Standard value: At idle: 29 kPa (4.2 psi) or more. At 3,500 r/min: 294 - 686 kPa (43 - 100 psi) | ||
| Overhaul | SERVICE SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | 74 +/- 2 N.m (54 +/- 1 ft-lb) | ||
| Fuel System | |||
| Pressure Specification | Standard value: Approximately 324 kPa (95.7 in. Hg) at curb idle | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE TEST | ||
| Fuel Filter Location | FUEL PUMP MODULE REPLACEMENT | ||
| Fuel Filter R & I | FUEL PUMP MODULE REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | NA | ||
| Ignition Wires (Routing) | NA | ||
| Spark Plug | |||
| Type | NGK; FR6EI - DENSO; K20PSR-B8 | ||
| Gap | Standard Value: .028-0.031 in. (0.7-0.8 mm). Limit: 1.2 mm (0.047 inch) | ||
| Torque | 25 +/- 5 N.m (18 +/- 4 ft-lb). | ||
| Starting | |||
| Starter | SERVICE SPECIFICATIONS | ||
| Torque | REMOVAL AND INSTALLATION | ||
| Wheel Alignment | |||
| Adjustment Specifications | |||
| Front | SERVICE SPECIFICATIONS | ||
| Rear | SERVICE SPECIFICATIONS | ||
| Torque | |||
| Front | FASTENER TIGHTENING SPECIFICATIONS | ||
| Rear | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 73+/-7 ft. lbs. (98+/-10 N.m) | ||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.