Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2004MATRIX XR, FWD, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 364 (AIR BAG RESTRAINT SYSTEMS)
2004 Toyota Matrix XR, FWD, Standard
Section 364 (Air Bag Restraint Systems)
2004 Toyota Matrix XR, FWD, StandardSECTION Section 364 (Air Bag Restraint Systems)
WARNING: This page is about a different car, the 2004 Toyota RAV4. However, it is still accessible from the selected car via links, so may be relevant.
- Description & Operation
- Component Locations
- System Operation Check
- Air Bag Safety Precautions
- Disabling & Activating Air Bag System
- Disposal Procedures
- Post-Collision Inspection
- Removal & Installation
- Notes
- Air Bag Sensor Assembly
- Driver-Side Air Bag Module
- Front Air Bag Sensor
- Front Seat
- Headliner
- Passenger-Side Air Bag Module
- Rear Air Bag Sensor
- Rear Seat
- Seat Belt Buckle Switch
- Seat Belt PRETENSIONER
- Seat Position Sensor
- Side Air Bag Module
- Side Air Bag Sensor
- Side Curtain Air Bag Module
- Spiral Cable
- Steering Wheel
- Adjustments
- Wire Repair
- Torque Specifications
- Diagnostics
- Diagnostic Tests
- Notes
- Air Bag Warning Light Is Always Illuminated When Diagnostic Trouble Code (DTC) Is Not Output
- Air Bag Warning Light Does Not Illuminate
- Source Voltage Drop
- Diagnostic Trouble Codes (DTCS) Cannot Be Displayed, Or DTCS Are Displayed Without Data Link Connector 3 (DLC 3) Connection
- Air Bag Warning Light Intermittent
- DTC 31/B1000: Air Bag Sensor Assembly Malfunction
- DTC 13/B1610: Right Front Air Bag Sensor Malfunction
- DTC 14/B1615: Left Front Air Bag Sensor Malfunction
- DTC 21/B1620: Left Side Air Bag Sensor Malfunction
- DTC 22/B1625: Right Side Air Bag Sensor Malfunction
- DTC 23/B1630: Left Rear Air Bag Sensor Malfunction
- DTC 22/B1635: Right Rear Air Bag Sensor Malfunction
- DTC 35/B1653: Seat Position Sensor Malfunction
- DTC 37/B1655: Left Seat Belt Switch Malfunction
- DTC 51/B1800, 51/B1801, 51/B1802, 51/B1803: Driver-Side Air Bag No. 1 Squib Circuit Short, Open, Short To Ground Or Short To Battery
- DTC 52/B1805, 52/B1806, 52/B1807, 52/B1808: Passenger-Side Air Bag No. 1 Squib Circuit Short, Open, Short To Ground Or Short To Battery
- DTC 53/B1810, 53/B1811, 53/B1812, 53/B1813: Driver-Side Air Bag No. 2 Squib Circuit Short, Open, Short To Ground Or Short To Battery
- DTC 54/B1815, 54/B1816, 54/B1817, 54/B1818: Passenger-Side Air Bag No. 2 Squib Circuit Short, Open, Short To Ground Or Short To Battery
- DTC 55/B1820, 55/B1821, 55/B1822, 55/B1823: Left Side Air Bag Squib Circuit Short, Open, Short To Ground Or Short To Battery
- DTC 56/B1825, 56/B1826, 56/B1827, 56/B1828: Right Side Air Bag Squib Circuit Short, Open, Short To Ground Or Short To Battery
- DTC 57/B1830, 57/B1831, 57/B1832, 57/B1833: Left Side Curtain Air Bag Squib Circuit Short, Open, Short To Ground Or Short To Battery
- DTC 58/B1835, 58/B1836, 58/B1837, 58/B1838: Right Side Curtain Air Bag Squib Circuit Short, Open, Short To Ground Or Short To Battery
- DTC 73/B1900, 73/B1901, 73/B1902, 73/B1903: Left Seat Belt PRETENSIONER Squib Circuit Short, Open, Short To Ground Or Short To Battery
- DTC 74/B1905, 74/B1906, 74/B1907, 74/B1908: Right Seat Belt PRETENSIONER Squib Circuit Short, Open, Short To Ground Or Short To Battery
- Wiring Diagrams
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.