Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSUBARU2022IMPREZA BASE, 4D SEDAN, AUTOMATIC CVT TRANSREPAIR AND DIAGNOSISBRAKESTRACTION CONTROLBRAKE CONTROL SYSTEM (DIAGNOSTICS) (EXCEPT HEV)WARNING LIGHT ILLUMINATION PATTERNINSPECTION
2022 Subaru Impreza Base, 4D Sedan, Automatic CVT Trans
Warning Light Illumination Pattern: Inspection
2022 Subaru Impreza Base, 4D Sedan, Automatic CVT TransSECTION Inspection
NOTE:
Hill start assist warning light always illuminates when the hill start assist is in the OFF mode.
- When warning lights or indicator lights do not illuminate in accordance with this illumination pattern, there must be an electrical malfunction.
- When the warning lights or indicator lights remain constantly OFF, check the combination meter circuit. Ref. to BRAKE CONTROL (DIAGNOSTICS)>WARNING LIGHT ILLUMINATION PATTERN>EBD WARNING LIGHT, ABS WARNING, VDC OFF INDICATOR LIGHT, VDC WARNING LIGHT AND VDC INDICATOR LIGHT DO NOT COME ON . Ref. to BRAKE CONTROL (DIAGNOSTICS)>WARNING LIGHT ILLUMINATION PATTERN>HILL START ASSIST WARNING LIGHT DOES NOT COME ON .
- When the ABS warning light, VDC OFF indicator light, VDC warning light and VDC indicator light, and hill start assist warning light do not go off, check the combination meter circuit or CAN communication circuit. Ref. to BRAKE CONTROL (DIAGNOSTICS)>WARNING LIGHT ILLUMINATION PATTERN>ABS WARNING LIGHT DOES NOT GO OFF . Ref. to BRAKE CONTROL (DIAGNOSTICS)>WARNING LIGHT ILLUMINATION PATTERN>VDC OFF INDICATOR LIGHT DOES NOT GO OFF . Ref. to BRAKE CONTROL (DIAGNOSTICS)>WARNING LIGHT ILLUMINATION PATTERN>VDC WARNING LIGHT AND VDC INDICATOR LIGHT DO NOT GO OFF . Ref. to BRAKE CONTROL (DIAGNOSTICS)>WARNING LIGHT ILLUMINATION PATTERN>HILL START ASSIST WARNING LIGHT DOES NOT GO OFF .
NOTE:
- Even when the ABS warning light and the VDC warning light and VDC indicator light do not go off in 2 seconds after illuminating, the ABS and VDC functions are normal if the warning lights go off while the vehicle is driven. However, while these lights are on, the functions with their warning lights illuminated do not operate.
- It may take several minutes before the VDC warning light and VDC indicator light goes off, if the vehicle is parked under low temperature for a specified time. This is not defective because it is resulted from low engine coolant temperature. Perform the Clear Memory Mode because DTC may be recorded at this time. Ref. to COMMON (DIAG)>CLEAR MEMORY .
- With the vehicle jack-up/lift-up or set on free rollers, when the wheels lock or spin after starting the engine, ABS warning light, and VDC warning light and VDC indicator light may illuminate because VDCCM and H/U detects the abnormal conditions from ABS wheel speed sensor or longitudinal G sensor. In this case, this is not a malfunction. Clear the memory. Ref. to COMMON (DIAG)>CLEAR MEMORY .
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.