Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2014 Mazda 5 TouringFACTORY OEM SERVICE PROCEDURE
Symptom Troubleshooting - Engine
- Foreword
- Engine Control System Symptom Diagnostic Index
- Engine Control System Device And Control Relationship Table
- Quick Diagnostic Table
- No. 1 Blown Fuses
- No. 2 Check Engine Light Illuminates
- No. 3 Will Not Crank
- No. 4 Hard To Start/Long Crank/Erratic Start/Erratic Crank
- No. 5 Engine Stalls-After Start/At Idle
- No. 6 Cranks Normally But Will Not Start
- No. 7 Slow Return To Idle
- No. 8 Engine Runs Rough/Rolling Idle
- No. 9 Fast Idle/Runs On
- No. 10 Low Idle/Stalls During Deceleration
- No. 11 Engine Stalls/Quits, Engine Runs Rough, Misses, Buck/Jerk, Hesitation/Stumble, Surges
- No. 12 Lack/Loss Of Power-Acceleration/Cruise
- No. 13 Knocking/Pinging-Acceleration/Cruise
- No. 14 Poor Fuel Economy
- No. 15 Emission Compliance
- No. 16 High Oil Consumption/Leakage
- No. 17 Cooling System Concerns-Overheating
- No. 18 Cooling System Concerns-Runs Cold
- No. 19 Exhaust Smoke
- No. 20 Fuel Odor (In Engine Compartment)
- No. 21 Engine Noise
- No. 22 Vibration Concerns (Engine)
- No. 23 A/C Does Not Work Sufficiently
- No. 24 A/C Is Always On Or A/C Compressor Runs Continuously
- No. 25 A/C Is Not Cut Off Under Wide Open Throttle Conditions
- No. 26 Exhaust Sulphur Smell
- No. 27 Fuel Refill Concerns
- No. 28 Fuel Filling Shut Off Concerns
- No. 29 Spark Plug Condition
- Intermittent Concern Troubleshooting
- Engine Control System Operation Inspection
- Input Signal System Inspection Procedure
- Main Relay Operation Inspection
- Intake Manifold Vacuum Inspection
- Drive-by-wire Control System Inspection
- Variable Intake Air Control Operation Inspection
- Variable Tumble Control Operation Inspection
- Fuel Injector Operation Inspection
- Fuel Cut Control System Inspection
- Fuel Pump Operation Inspection
- Fuel Pump Control System Inspection
- Spark Test
- EGR Control System Inspection
- Purge Control System Inspection
- A/C Cut-off Control System Inspection
- Cooling Fan Control System Inspection
- Variable Valve Timing Control System Operation Inspection
- Evaporative Emission (EVAP) System Leak Inspection
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.