Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMAZDA20133 MAZDASPEED, 2.3L ENG VIN 3REPAIR AND DIAGNOSIS (SINGLE PAGE)BRAKESTRACTION CONTROLON-BOARD DIAGNOSTIC [DYNAMIC STABILITY CONTROL SYSTEM]
2013 Mazda 3 Mazdaspeed, 2.3L Eng VIN 3
On-Board Diagnostic [Dynamic Stability Control System]
2013 Mazda 3 Mazdaspeed, 2.3L Eng VIN 3SECTION On-Board Diagnostic [Dynamic Stability Control System]
- Dynamic Stability Control System Wiring Diagram [Dynamic Stability Control (DSC)]
- Foreword [Dynamic Stability Control (DSC)]
- On-Board Diagnosis [Dynamic Stability Control (DSC)]
- DTC B10DF:46/C0082:47/C0082:48/C0082:49/C1B14:01/U2007:46 [DSC HU/CM (internal malfunction)]
- DTC C0001:01/C0002:01/C0003:01/C0004:01/C0010:01/C0011:01/C0014:01/C0015:01/C0018:01/C0019:01/C001C:01/C001D:01 [Traction control solenoid valve system]
- DTC C0020:01/C0020:1C/C0020:71 [Pump motor, motor relay]
- DTC C0030:07/C0031:07/C0033:07/C0034:07/C0036:07/C0037:07/C0039:07/C003A:07 [ABS sensor rotor]
- DTC C0031:01/C0034:01/C0037:01/C003A:01 [ABS wheel-speed sensor]
- DTC C0040:64 [Brake switch]
- DTC C0044:01/C0044:28/C0044:54/C0044:64 [Brake fluid pressure sensor]
- DTC C0051:28 [Steering angle sensor]
- DTC C0061:28/C0061:64/C0063:28/C0063:64 [SAS control module system]
- DTC C0061:54/C0063:54 [DSC HU/CM (Unperformed initialization procedure)]
- DTC C006B:00/C0072:68 [TCS/DSC control system]
- DTC C1109:64 [DSC OFF switch]
- DTC U0001:88/U0100:00/U0101:00/U0140:00/U0155:00 [CAN line]
- DTC U0151:00 [SAS control module system (CAN2 line malfunction)]
- DTC U0401:00 [Abnormal message from PCM]
- DTC U0402:00 [Abnormal message from PCM (MTX)/(ATX)]
- DTC U0422:00/U0428:62/U0428:64 [Abnormal message from BCM]
- DTC U0452:86 [Abnormal message from SAS control module]
- DTC U2100:00/U2101:00 [Configuration data not recorded]
- DTC U3003:08/U3003:16/U3003:17 [Power supply system]
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.