Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSHYUNDAI2014ACCENT SE, STANDARD TRANSREPAIR AND DIAGNOSIS (SINGLE PAGE)BRAKESANTI-LOCK BRAKESANTILOCK BRAKE SYSTEM/ELECTRONIC STABILITY CONTROL SYSTEM DIAGNOSIS
2014 Hyundai Accent SE, Standard Trans
Antilock Brake System/Electronic Stability Control System Diagnosis
2014 Hyundai Accent SE, Standard TransSECTION Antilock Brake System/Electronic Stability Control System Diagnosis
- DTC Index
- DTC C1101: Battery Voltage High
- DTC C1102: Battery Voltage Low
- DTC C1112: Sensor source voltage
- DTC C1200: Wheel Speed Sensor Front-LH Open/Short
- DTC C1201: Wheel Speed Sensor Front-LH Range/Performance/Intermittent
- DTC C1202: Wheel Speed Sensor Front-LH Invalid/no Signal
- DTC C1203: Wheel Speed Sensor Front-RH Open/Short
- DTC C1204: Wheel Speed Sensor Front-RH Range/Performance/Intermittent
- DTC C1205: Wheel Speed Sensor Front-RH Invalid/no Signal
- DTC C1206: Wheel Speed Sensor Rear-LH Open/Short
- DTC C1207: Wheel Speed Sensor Rear-LH Range/Performance/Intermittent
- DTC C1208: Wheel Speed Sensor Rear-LH Invalid/no Signal
- DTC C1209: Wheel Speed Sensor Rear-RH Open/Short
- DTC C1210: Wheel Speed Sensor Rear-RH Range/Performance/Intermittent
- DTC C1211: Wheel Speed Sensor Rear-RH Invalid/no Signal
- DTC C1235: Primary Pressure Sensor-Electrical
- DTC C1237: Primary Pressure Sensor-Signal
- DTC C1259: Steering Angle Sensor Electrical Malfunction
- DTC C1260: Steering Angle Sensor Circuit-Signal
- DTC C1282: Yaw Rate & Lateral G Sensor-Electrical
- DTC C1283: Yaw Rate & Lateral G Sensor-Signal
- DTC C1503: TCS/ESC (ESP) Switch error
- DTC C1513: Brake switch error
- DTC C1604: ECU Hardware Error
- DTC C1605: CAN Hardware error
- DTC C1611: CAN Time-out ECM
- DTC C1612: CAN Time-out TCM
- DTC C1613: CAN Wrong Message
- DTC C1616: CAN Bus off
- DTC C1687: CAN Time-out MDPS
- DTC C1688: MDPS signal error
- DTC C1702: Variant Coding Error
- DTC C2112: Valve Relay Error
- DTC C2130: Brake Lamp Relay
- DTC C2227: Excessive Temperature Of Brake Disc
- DTC C2380: ABS/TCS/ESC (ESP) valve error
- DTC C2402: Motor Failure
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.