Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Diagnostic Trouble Code (DTC) Chart
2021 Ford Edge SE, 4WDSECTION Diagnostic Trouble Code (DTC) Chart
WARNING: This page is about a different car, the 2021 Ford F-150. However, it is still accessible from the selected car via links, so may be relevant.
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
Diagnostic Trouble Code Chart
| Module | DTC | Description | Action |
|---|---|---|---|
| PSCM | B1D23:4B | Overheat Sensor: Over Temperature | GO to Pinpoint Test BB |
| PSCM | C102D:00 | High Friction Inside Power Steering: No Sub Type Information | GO to Pinpoint Test K |
| PSCM | C1110:56 | Power steering Calibration Data: Invalid/Incompatible Configuration | GO to Pinpoint Test E |
| PSCM | C1B00:49 | Steering Angle Sensor: Internal Electronic Failure | GO to Pinpoint Test V |
| PSCM | C1B00:62 | Steering Angle Sensor: Signal Compare Failure | GO to Pinpoint Test U |
| PSCM | C200B:49 | Steering Shaft Torque Sensor 1: Internal Electronic Failure | GO to Pinpoint Test M |
| PSCM | C200B:62 | Steering Shaft Torque Sensor 1: Signal Compare Failure | GO to Pinpoint Test P |
| PSCM | C200C:49 | Steering Shaft Torque Sensor 2: Internal Electronic Failure | GO to Pinpoint Test N |
| PSCM | C200C:62 | Steering Shaft Torque Sensor 2: Signal Compare Failure | GO to Pinpoint Test Q |
| PSCM | C200D:49 | Motor Rotation Angle Sensor: Internal Electronic Failure | GO to Pinpoint Test O |
| PSCM | C200D:62 | Motor Rotation Angle Sensor: Signal Compare Failure | GO to Pinpoint Test R |
| PSCM | U0100:00 | Lost Communication With ECM / PCM "A": No Sub Type Information | GO to Pinpoint Test AA |
| PSCM | U0102:00 | Lost Communication with Transfer Case Control Module: No Sub Type Information | GO to Pinpoint Test CF |
| PSCM | U0121:00 | Lost Communication With Anti-lock Brake System (ABS) Control Module: No Sub Type Information | GO to Pinpoint Test AB |
| PSCM | U0122:00 | Lost Communication with Vehicle Dynamics Control Module: No Sub Type Information | GO to Pinpoint Test CG |
| PSCM | U0126:00 | Lost Communication with Steering Angle Sensor Module: No Sub Type Information | GO to Pinpoint Test AY |
| PSCM | U0137:00 | Lost Communication with Trailer Brake Control Module: No Sub Type Information | GO to Pinpoint Test CK |
| PSCM | U0140:00 | Lost Communication with Body Control Module: No Sub Type Information | GO to Pinpoint Test AL |
| PSCM | U0146:00 | Lost Communication With Serial Data Gateway "A": No Sub Type Information | GO to Pinpoint Test AM |
| PSCM | U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test AN |
| PSCM | U0155:00 | Lost Communication with Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AO |
| PSCM | U0159:00 | Lost Communication with Parking Assist Control Module "A": No Sub Type Information | GO to Pinpoint Test AP |
| PSCM | U0212:00 | Lost Communication with Steering Column Control Module: No Sub Type Information | GO to Pinpoint Test AQ |
| PSCM | U023A:00 | Lost Communication With Image Processing Module A: No Sub Type Information | GO to Pinpoint Test AR |
| PSCM | U023B:00 | Lost Communication with Image Processing Module B: No Sub Type Information | GO to Pinpoint Test BS |
| PSCM | U0252:00 | Lost Communication with Lighting Control Module- Rear: No Sub Type Information | GO to Pinpoint Test AZ |
| PSCM | U0253:00 | Lost Communication with Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test BT |
| PSCM | U0256:00 | Lost Communication with Front Controls Interface Module: No Sub Type Information | GO to Pinpoint Test CL |
| PSCM | U0401:00 | Invalid Data Received from Powertrain Control Module: No Sub Type Information | GO to Pinpoint Test S |
| PSCM | U0403:00 | Invalid Data Received from Transfer Case Control Module: No Sub Type Information | GO to Pinpoint Test CJ |
| PSCM | U0415:00 | Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information | GO to Pinpoint Test T |
| PSCM | U0415:22 | Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A": Signal Amplitude Greater Than Maximum | GO to Pinpoint Test T |
| PSCM | U0416:00 | Invalid Data Received from Vehicle Dynamics Control Module: No Sub Type Information | GO to Pinpoint Test CA |
| PSCM | U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test BU |
| PSCM | U0423:00 | Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information | GO to Pinpoint Test BW |
| PSCM | U0428:00 | Invalid Data Received from the Steering Angle Sensor Module: No Sub Type Information | GO to Pinpoint Test BV |
| PSCM | U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information | GO to Pinpoint Test BX |
| PSCM | U045A:00 | Invalid Data Received from the Parking Assist Control Module: No Sub Type Information | GO to Pinpoint Test AW |
| PSCM | U053B:00 | Invalid Data Received From Image Processing Module A: No Sub Type Information | GO to Pinpoint Test AX |
| PSCM | U053C:00 | Invalid Data Received From Image Processing Module B: No Sub Type Information | GO to Pinpoint Test BY |
| PSCM | U0553:00 | Invalid Data Received From The Lighting Control Module - Rear: No Sub Type Information | GO to Pinpoint Test BM |
| PSCM | U0554:00 | Invalid Data Received From The Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test CD |
| PSCM | U0557:00 | Invalid Data Received From Front Controls Interface Module "A": No Sub Type Information | GO to Pinpoint Test CM |
| PSCM | U2014:78 | Control Module Hardware: Alignment Or Adjustment Incorrect | GO to Pinpoint Test J |
| PSCM | U2014:81 | Control Module Hardware: Invalid Serial Data Received | GO to Pinpoint Test J |
| PSCM | U2014:92 | Control Module Hardware: Performance Or Incorrect Operation | GO to Pinpoint Test J |
| PSCM | U2016:47 | Control Module Main Software: Watchdog/Safety μC Failure | GO to Pinpoint Test W |
| PSCM | U2016:48 | Control Module Main Software: Supervision Software Failure | GO to Pinpoint Test W |
| PSCM | U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test Y |
| PSCM | U2300:55 | Central Configuration: Not Configured | GO to Pinpoint Test F |
| PSCM | U2300:56 | Central Configuration: Invalid/Incompatible Configuration | GO to Pinpoint Test F |
| PSCM | U3000:42 | Control Module: General Memory Failure | GO to Pinpoint Test C |
| PSCM | U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test C |
| PSCM | U3000:61 | Control Module: Signal Calculation Failure | GO to Pinpoint Test C |
| PSCM | U3000:96 | Control Module: Component Internal Failure | GO to Pinpoint Test B |
| PSCM | U3001:68 | Control Module Improper Shutdown Performance: Event Information | GO to Pinpoint Test BD |
| PSCM | U3001:89 | Control Module Improper Shutdown Performance: Data Transfer Failure | GO to Pinpoint Test BD |
| PSCM | U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test X |
| PSCM | U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test X |
| PSCM | U3003:18 | Battery Voltage: Circuit Current Below Threshold | GO to Pinpoint Test X |
| PSCM | U3003:19 | Battery Voltage: Circuit Current Above Threshold | GO to Pinpoint Test X |
| PSCM | U3003:68 | Battery Voltage: Event Information | GO to Pinpoint Test X |
| PSCM | U3003:A2 | Battery Voltage: System Voltage Low | GO to Pinpoint Test X |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.