Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2010MUSTANG BASE, 2D COUPE, AUTOMATICREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 266 (AUTOMATIC TRANSMISSION)
2010 Ford Mustang Base, 2D Coupe, Automatic
Section 266 (Automatic Transmission)
2010 Ford Mustang Base, 2D Coupe, AutomaticSECTION Section 266 (Automatic Transmission)
WARNING: This page is about a different car, the 2006 Mercury Grand Marquis and 2006 Ford Crown Victoria. However, it is still accessible from the selected car via links, so may be relevant.
- Specifications
- General Specification
- Line Pressure Specification Chart
- Band And Clutch Specification Chart A
- Band And Clutch Application Chart B
- Stall Speed Chart
- Shift Speed Specification Chart
- Sensor Resistance Readings Specification
- Solenoid Operation Specification Chart
- Gear Ratio Specification
- Selective Thrust Washer Specification
- Forward Clutch Pack Specification
- Reverse Clutch Pack Specification
- Direct Clutch Pack Specification
- Intermediate Clutch Pack Specification
- Torque Specification
- Description And Operation
- Transmission Description
- Identification Tags
- Range Selection
- Shift Patterns
- Bushings, Bearing and Thrust Washer Locator
- Seals, Rings and Gasket Locator
- Main Components and Functions
- Torque Converter
- Geartrain
- Apply Components
- Hydraulic System
- Transmission Electronic Control System
- Notes
- Powertrain Control Module (PCM)
- Air Conditioning (A/C) Clutch
- Brake Pedal Position (BPP) Switch
- Engine Coolant Temperature (ECT) Sensor
- Ignition Coil - Coil On Plug
- Intake Air Temperature (IAT) Sensor
- Mass Air Flow (MAF) Sensor
- Transmission Control Switch (TCS) and Transmission Control Indicator Lamp (TCIL)
- Throttle Position (TP) Sensor
- Digital Transmission Range (TR) Sensor
- Output Shaft Speed (OSS) Sensor
- Turbine Shaft Speed (TSS) Sensor
- Electronic Pressure Control (EPC) Solenoid
- Torque Converter Clutch (TCC) Solenoid
- Shift Solenoid - SSA, SSB
- Transmission Fluid Temperature (TFT) Sensor
- Diagnosis And Testing
- Diagnostic Strategy
- Diagnostic Flow Chart
- Preliminary Inspection
- Road Testing Vehicle
- Shift Point Road Test
- Torque Converter Diagnosis
- Visual Inspection
- Diagnostics
- Output State Control (OSC) Mode
- Transmission Drive Cycle Test
- Diagnostic Trouble Code (DTC) Charts
- Transmission Connector Layouts
- Transmission Vehicle Harness Connector
- Transmission Internal Harness Connector
- Digital Transmission Range (TR) Sensor Connector
- Output Shaft Speed (OSS) Sensor Harness Connector
- Turbine Shaft Speed (TSS) Sensor Harness Connector
- Powertrain Control Module (PCM) Harness Connector
- Digital Transmission Range (TR) Sensor Diagnosis Chart
- Wiggle Test Information For Open/Shorts
- Pinpoint Tests - OSC Equipped Vehicle
- Notes
- Shift Solenoids Pre-Diagnosis
- Pinpoint Tests
- Pinpoint Test A: Shift And Torque Converter Clutch Solenoids
- Pinpoint Test B: Transmission Fluid Temperature (TFT) Sensor
- Pinpoint Test C: Digital Transmission Range (Tr) Sensor
- Pinpoint Test D: Electrical Pressure Control (EPC) Solenoid
- Pinpoint Test E: Output Shaft Speed (OSS) Sensors
- Pinpoint Test F: Turbine Shaft Speed Sensors
- Pinpoint Test G: Solenoid Mechanical Failure
- Special Testing Procedures
- Leakage Inspection
- Transmission Fluid Cooler
- Diagnosis By Symptom
- Notes
- Diagnosis by Symptom Chart Directions
- Diagnostic Routines
- Engagement Concern: No Forward
- Engagement Concern: No Reverse
- Engagement Concern: Harsh Reverse
- Engagement Concern: Harsh Forward
- Engagement Concern: Delayed/Soft Reverse
- Engagement Concern: Delayed/Soft Forward
- Shift Concerns: Some/All Shifts Missing
- Shift Concerns: Timing Concerns - Early/Late
- Shift Concerns: Timing Concerns - Erratic/Hunting
- Shift Concerns: Feel - Soft/Slipping
- Shift Concerns: Feel - Harsh
- Shift Concerns: No 1st Gear, Engages In Higher Gear
- Shift Concerns: No Manual 1st Gear
- Shift Concerns: No Manual 2nd Gear
- Shift Concerns: 1-2 Shift (Automatic)
- Shift Concerns: 2-3 Shift (Automatic)
- Shift Concerns: 3-4 Shift (Automatic)
- Shift Concerns: 4-3 Shift (Automatic)
- Shift Concerns: 3-2 Shift (Automatic)
- Shift Concerns: 2-1 Shift (Automatic)
- Torque Converter Clutch Operation Concerns: No Apply
- Torque Converter Clutch Operation Concerns: Always Applied/Stalls Vehicle
- Torque Converter Clutch Operation Concerns: Cycling/Shudder/Chatter
- Other Concerns: No Engine Braking In Manual 2nd Or Manual 1st Position
- Other Concerns: Shift Lever Efforts High
- Other Concerns: External Leaks
- Other Concerns: Poor Vehicle Performance
- Other Concerns: Noise/Vibration - Forward Or Reverse
- Other Concerns: Engine Will Not Crank
- Other Concerns: No Park (P) Range
- Other Concerns: Overheating
- General Procedures
- In-Vehicle Repair
- Fluid Pan, Gasket and Filter
- Transmission Filler Tube
- Main Control Valve Body
- Extension Housing Gasket
- Extension Housing Seal
- Electronic Pressure Control (EPC) Solenoid
- Manual Control Lever Shaft and Seal
- Digital Transmission Range (TR) Sensor
- Reverse Servo Assembly
- Overdrive Servo
- 1-2 Accumulator
- 2-3 Accumulator
- Transmission Insulator and Retainer
- Transmission Support Crossmember
- Turbine Shaft Speed (TSS) Sensor
- Output Shaft Speed (OSS) Sensor
- Removal
- Disassembly
- Disassembly And Assembly Of Subassemblies
- Assembly
- Installation
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.