Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DBβ LIVE
HOMESERVICE MANUALSDODGE AND RAM20241500 TRXREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 292 ((DRIVERS ASSISTANCE SYSTEM MODULE - ELECTRICAL DIAGNOSTICS - 1500))
2024 Dodge and Ram 1500 TRX
Section 292 ((Drivers Assistance System Module - Electrical Diagnostics - 1500))
2024 Dodge and Ram 1500 TRXSECTION Section 292 ((Drivers Assistance System Module - Electrical Diagnostics - 1500))
WARNING: This page is about a different car, the 2023 RAM 1500. However, it is still accessible from the selected car via links, so may be relevant.
- Diagnostic Code Index
- DTC Troubleshooting
- B1EAD-2A-Lane Departure Warning Switch-Stuck
- C0063-9A-Yaw Rate Sensor-Component Or System Operating Conditions
- C008E-00-Ecu Internal Performance
- C008F-00-Calibration Not Learned
- C1240-00-Steering Angle Sensor Angle OVERTRAVEL Performance
- C127A-00-Esp Did Not Respond To Deceleration Request
- C14A3-00-XBW Rule Violation
- C14A4-00-Sensor Adjustment Required
- C14A5-00-Sensor Blinded
- C14A6-92-Vehicle Reaction-Performance Or Incorrect Operation
- C2129-16-Battery Voltage-Circuit Voltage Below Threshold
- C2129-17-Battery Voltage-Circuit Voltage Above Threshold
- C212A-84-System Voltage-Signal Below Allowable Range
- C212A-85-System Voltage-Signal Above Allowable Range
- C2206-00-Vehicle Configuration Mismatch
- C2210-00-Ecu OVERTEMPERATURE
- C2212-00-Ecu In-Plant Mode
- C2223-00-Ecu Configuration Mismatch
- C2225-00-Pcm Disabled Ecu
- C2226-00-TCM Disabled Ecu
- C2227-00-Abs Disabled Ecu
- P0585-00-Speed Control Switch 1/2 Correlation
- P1593-2A-Speed Control Switch 1/2 - Stuck
- U0002-00-Can C Bus Off Performance
- U0100-00-Lost Communication With ECM/Pcm
- U0101-00-Lost Communication With TCM
- U0102-00-Lost Communication With Transfer Case Control Module / AWD
- U0121-00-Lost Communication With Anti-Lock Brake System (Abs) Control Module
- U0131-00-Lost Communication With Electric Power Steering Control Module
- U0132-00-Lost Communication With Suspension Control Module
- U0137-00-Lost Communication With Trailer Brake Control Module
- U0140-00-Lost Communication With Body Control Module
- U0151-00-Lost Communication With Occupant Restraint Controller (Orc)
- U0155-00-Lost Communication With Cluster-CCN
- U0401-00-Implausible Data Received From ECM/Pcm
- U0402-00-Implausible Data Received From TCM
- U0403-00-Implausible Data Received From TCASE
- U0415-00-Implausible Data Received From Abs
- U0420-00-Invalid Data Received From Power Steering Control Module
- U0421-00-Implausible Data Received From Suspension Control Module
- U0422-00-Implausible Data Received From Body Control Module
- U0423-00-Implausible Data Received From Cluster-CCN
- U0429-00-Implausible Data Received From Steering Column Control Module
- U0438-00-Implausible Data Received From Trailer Control Module
- U0452-00-Implausible Data Received From Restraints Control Module
- U110A-00-Lost Communication With SCM - Can-C
- U115F-00-Lost Communication With Driver Presence Detection Module
- U11F9-00 - Engine Did Not Respond To Acc Torque Request
- U121E-00-Lost Communication With Steering Wheel Cruise Control Switch
- U141E-00-Implausible Data Received From Cruise Control Switch
- U1442-00-Implausible Data Received From Driver Presence Detection Module
- U1600-00 - Ecu Application Software Mismatch
- Standard Procedure
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.