Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSDODGE AND RAM1995INTREPID ES, 3.3 UREPAIR AND DIAGNOSISQUICK LOOKUPSCOMMON SPECS & PROCEDURESSPECIFICATIONS INDEX
1995 Dodge and Ram Intrepid ES, 3.3 U
Specifications Index
1995 Dodge and Ram Intrepid ES, 3.3 USECTION Specifications Index
CONCORDE, INTREPID, LHS, NEW YORKER & VISION SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning - Automatic System | |||
| Service | A/C SYSTEM SPECIFICATIONS - AUTOMATIC | ||
| Torque | N/A | ||
| Air Conditioning - Manual System | |||
| Service | A/C SYSTEM SPECIFICATIONS - MANUAL | ||
| Torque | N/A | ||
| Axle Nut/Hub Nut | 120 Ft. Lbs. (163 N.m) | ||
| Battery | |||
| 3.3L | CAPACITIES | ||
| 3.5L | CAPACITIES | ||
| Brakes | |||
| Bleeding Sequence | |||
| With ABS | BLEEDING BRAKE SYSTEM | ||
| Without ABS | BLEEDING PROCEDURES | ||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drum Brakes | |||
| Service Specifications | DRUM BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | N/A | ||
| Torque | N/A | ||
| Drive Belts | |||
| Adjustment | BELT ADJUSTMENT SPECIFICATIONS | ||
| Drive Belt Routing | BELT ROUTING | ||
| Engine Cooling | |||
| General Service Specifications | COOLING SYSTEM SPECIFICATIONS | ||
| Radiator Cap Pressure | 14-18 psi | ||
| Thermostat R & I | |||
| 3.3L | ENGINE THERMOSTATS | ||
| 3.5L | ENGINE THERMOSTATS | ||
| Water Pump R & I | |||
| 3.3L | WATER PUMP | ||
| 3.5L | WATER PUMP | ||
| Engine Mechanical | |||
| 3.3L | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure |
Normal oil pressure is 5 psi (.35 kg/cm2 ) at curb idle and 30-80 psi (2.1-5.5 kg/cm2 ) at 3000 RPM. |
||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 3.5L | |||
| Compression | ENGINE COMPRESSION | ||
| Oil pressure | OIL PRESSURE | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | 75 Ft. Lbs. (101 N.m) | ||
| Fuel System | |||
| Pressure Specification | 125 psi (8.8 kg/cm2) | ||
| Fuel Pressure Test Procedure | |||
| 3.3L | FUEL PRESSURE | ||
| 3.5L | FUEL PRESSURE | ||
| Fuel Filter Location | |||
| 3.3L | FUEL FILTER | ||
| 3.5L | FUEL FILTER | ||
| Fuel Filter R & I | |||
| 3.3L | FUEL FILTER | ||
| 3.5L | FUEL FILTER | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 3.3L | FIRING ORDER & TIMING MARKS | ||
| 3.5L | FIRING ORDER & TIMING MARKS | ||
| Ignition Wires (Resistance) | N/A | ||
| Ignition Wires (Routing) | |||
| 3.3L | FIRING ORDER & TIMING MARKS | ||
| 3.5L | FIRING ORDER & TIMING MARKS | ||
| Spark Plug | |||
| 3.3L | SPARK PLUGS | ||
| 3.5L | SPARK PLUGS | ||
| Starting | |||
| Starter | |||
| Concorde, Intrepid, & Vision | STARTER SPECIFICATIONS | ||
| LHS & New Yorker | STARTER SPECIFICATIONS | ||
| Torque | |||
| Concorde, Intrepid, & Vision | TORQUE SPECIFICATIONS | ||
| LHS & New Yorker | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | |||
| Concorde, LHS & New Yorker | ALIGNMENT SPECIFICATIONS | ||
| Intrepid | ALIGNMENT SPECIFICATIONS | ||
| Vision | ALIGNMENT SPECIFICATIONS | ||
| Torque | |||
| Concorde, LHS & New Yorker | TORQUE SPECIFICATIONS | ||
| Intrepid | TORQUE SPECIFICATIONS | ||
| Vision | TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | |||
| Step 1 | 47 Ft. Lbs. (64 N.m) | ||
| Step 2 | 95 Ft. Lbs. (129 N.m) | ||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.