Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2013CAMARO ZL1, 2D COUPE, AUTOMATIC TRANSREPAIR AND DIAGNOSISGENERAL INFORMATIONSPECIFICATIONS INDEXCOMMON SPECS AND PROCEDURESCOMMON SPECS & PROCEDURES INDEX
2013 Chevrolet Camaro ZL1, 2D Coupe, Automatic Trans
Common Specs & Procedures Index
2013 Chevrolet Camaro ZL1, 2D Coupe, Automatic TransSECTION Common Specs & Procedures Index
CAMARO COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | N/A | ||
| Rear | 199 lb ft (270 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | Manual
- RIGHT REAR, LEFT REAR, RIGHT FRONT, LEFT FRONT HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) Pressure - RIGHT REAR, LEFT REAR, RIGHT FRONT, LEFT FRONT See HYDRAULIC BRAKE SYSTEM BLEEDING (PRESSURE) . |
||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | See illustration under DRIVE BELT REPLACEMENT for 3.6L or for 6.2L, see SUPERCHARGER BELT REPLACEMENT and DRIVE BELT REPLACEMENT - ACCESSORY (LSA) orDRIVE BELT REPLACEMENT - ACCESSORY (EXCEPT LSA) | ||
| Engine Cooling | |||
| General Service Specifications | N/A | ||
| Radiator Cap Pressure | Pressure Stamped On Cap | ||
| Thermostat R & I | |||
| 3.6L | ENGINE COOLANT THERMOSTAT REPLACEMENT (LFX) | ||
| 6.2L | ENGINE COOLANT THERMOSTAT REPLACEMENT (L99/LS3) or ENGINE COOLANT THERMOSTAT REPLACEMENT (LSA) | ||
| Water Pump R & I | |||
| 3.6L | WATER PUMP REPLACEMENT (LFX) | ||
| 6.2L | WATER PUMP REPLACEMENT (LS3/L99) or WATER PUMP REPLACEMENT (LSA) | ||
| Engine Mechanical | |||
| 3.6L | |||
| Compression | No cylinder reading should be less than 965 kPa (140 psi). The lowest reading should not be less than 70 percent of the highest reading See ENGINE COMPRESSION TEST |
||
| Oil Pressure | Minimum @ Idle 69kPa 10psi Minimum @ 2,000 RPM 138 kPa 20psi |
||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS (LFX) | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 6.2L | |||
| Compression | No cylinder should read less than 690 kPa (100 psi). The lowest reading should not be less than 70 percent of the highest reading See ENGINE COMPRESSION TEST |
||
| Oil pressure | 165 kPa @ 1,000 RPM 24 psig 241 kPa @ 2,000 RPM 35 psig 262 kPa @ 4,000 RPM 38 psig |
||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS (6.2L LS3) ENGINE MECHANICAL SPECIFICATIONS (6.2L L99) ENGINE MECHANICAL SPECIFICATIONS (6.2L LSA) |
||
| Torque | FASTENER TIGHTENING SPECIFICATIONS (6.2L LS3) FASTENER TIGHTENING SPECIFICATIONS (6.2L L99) FASTENER TIGHTENING SPECIFICATIONS (6.2L LSA) |
||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | Auto Trans 3.6 L First Pass (30 N.m) 22 lb ft Final Pass Additional 45 Degrees Manual Trans 3.6 L (67 N.m) 49 lb ft Auto Trans 6.2 L First Pass 20 N.m 15 lb ft 6.2 L Second Pass 50 N.m 37 lb ft 6.2 L Final Pass 100 N.m 74 lb ft Manual Trans 6.2L First Pass 50 N.m (37 lb ft) Final Pass Additional 45 degrees |
||
| Fuel System | |||
| Pressure Specifications | 3.6 L Engine at Idle 300-400 kPa (43-58 psi) see 6.2 L W/O Supercharger Engine at Idle 296.4-310.3 kPa (35-45 psi) see 6.2 L With Supercharger Engine at Idle 380-520 kPa (55-76 psi) see |
||
| Fuel Pressure Test Procedure | 3.6 L CIRCUIT/SYSTEM VERIFICATION 6.2 L Without Supercharger Circuit/System Verification 6.2L With Supercharger CIRCUIT/SYSTEM VERIFICATION |
||
| Fuel Filter Location | 3.6 L Fuel Filter is Part of the Fuel Tank Fuel Pump Module 6.2 L Fuel Filter is Part of the Fuel Tank Fuel Pump Module |
||
| Fuel Filter R & I | 3.6 L FUEL TANK FUEL PUMP MODULE REPLACEMENT - RIGHT SIDE | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | 3.6 L Individual Ignition Coil/Module Assemblies 6.2 L Individual Ignition Coil/Module Assemblies |
||
| Ignition Wires (Routing) | |||
| 3.6 L | Coil on Plug | ||
| 6.2 L | Coil on Plug | ||
| Spark Plug | |||
| 3.6L - Type See parts catalog | |||
| Gap | (0.95-1.10 mm) 0.0375-0.0433 in | ||
| Torque | (18 N.m) 13 lb ft | ||
| 6.2L - Type See parts catalog | |||
| Gap | (1.02 mm) 0.40 in | ||
| Torque | (15 N.m) 11 lb ft | ||
| Starting | |||
| Starter | N/A | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | Wheel Nuts with silver tint cone seats (W/ RPO RT2 - WHEEL-18 X 7.5, J, STEEL, DESIGN 1) (190 N.m) 140 lb. ft Wheel Nuts with blue tint cone seats (W/ RPO RT2 - WHEEL-18 X 7.5, J, STEEL, DESIGN 1) (150 N.m) 110 lb ft Wheel Nut Torque (W/O RPO RT2) (165 N.m) 122 lb ft For wheel nut tightening sequence, see illustration under TIRE AND WHEEL REMOVAL AND INSTALLATION (WITHOUT RT2 - STEEL WHEELS) or TIRE AND WHEEL REMOVAL AND INSTALLATION (WITH RT2 - STEEL WHEELS) . |
||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.