Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2013CAMARO ZL1, 2D COUPE, AUTOMATIC TRANSREPAIR AND DIAGNOSISSUSPENSIONWHEEL ALIGNMENTWHEEL ALIGNMENT SYSTEMSPECIFICATIONSWHEEL ALIGNMENT SPECIFICATIONS
2013 Chevrolet Camaro ZL1, 2D Coupe, Automatic Trans
Wheel Alignment Specifications
2013 Chevrolet Camaro ZL1, 2D Coupe, Automatic TransSECTION Wheel Alignment Specifications
Alignment Condition: Full tank of fuel, no passengers and placed on flat level surface.
Wheel Alignment Specifications
| RPO Restriction | Wheels | Caster ± 0.75° |
Cross Caster ± 0.75° |
Camber ± 0.75° |
Cross Camber ± 0.75° |
Total Toe ± 0.2° |
Steering Wheel Angle ± 3.5° |
Thrust Angle ± 0.3° |
||
|---|---|---|---|---|---|---|---|---|---|---|
| Left | Right | (Left - Right) | Left | Right | (Left - Right) | (Left + Right) | (Left - Right)/2 | |||
| FE2 without WRS | Front | 5.9° | 5.9° | 0.0° | -0.2° | -0.2° | 0.0° | 0.2° | 0.0° | - |
| Rear | - | - | - | -0.75° | -0.75° | - | 0.2° | - | 0.0° | |
| FE2 with WRS | Front | 5.9° | 5.9° | 0.0° | -0.2° | -0.2° | 0.0° | 0.2° | 0.0° | - |
| Rear | - | - | - | -0.4° | -0.4° | - | 0.2° | - | 0.0° | |
| FE3 | Front | 5.9° | 5.9° | 0.0° | -0.8° | -0.8° | 0.0° | 0.2° | 0.0° | - |
| Rear | - | - | - | -0.4° | -0.4° | - | 0.2° | - | 0.0° | |
| FE4 | Front | 5.9° | 5.9° | 0.0° | -0.8° | -0.8° | 0.0° | 0.2° | 0.0° | - |
| Rear | - | - | - | -0.4° | -0.4° | - | 0.2° | - | 0.0° | |
| FE5 | Front | 5.6° | 5.6° | 0.0° | -1.0° | -1.0° | 0.0° | 0.2° | 0.0° | - |
| Rear | - | - | - | -0.5° | -0.5° | - | 0.2° | - | 0.0° | |
| FE6 | Front | 5.6° | 5.6° | 0.0° | -1.0° | -1.0° | 0.0° | 0.2° | 0.0° | - |
| Rear | - | - | - | -0.75° | -0.75° | - | 0.2° | - | 0.0° | |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.