Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2008CHEVY EXPRESS G2500, VAN CARGO, 6.6 6REPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 636 (INSTRUMENT PANEL, GAGES, AND CONSOLE)
2008 Chevrolet Chevy Express G2500, Van Cargo, 6.6 6
Section 636 (Instrument Panel, Gages, And Console)
2008 Chevrolet Chevy Express G2500, Van Cargo, 6.6 6SECTION Section 636 (Instrument Panel, Gages, And Console)
WARNING: This page is about a different car, the 2003 GMC Sierra, 2003 GMC Cab & Chassis Sierra, 2003 Chevrolet Silverado, and 2003 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.
- Specifications
- Schematic and Routing Diagrams
- Component Locator
- Diagnostic Information and Procedures
- Diagnostic Starting Point-Instrument Panel, Gages & Console
- Diagnostic System Check - Instrument Cluster
- Diagnostic System Check - Driver Information Systems
- Diagnostic System Check - Audible Warnings
- Scan Tool Output Controls
- Scan Tool Data List
- Scan Tool Data Definitions
- Diagnostic Trouble Code (DTC) List
- DTC B0540: Driver State Mismatch
- DTC B0560: Driver State Mismatch
- DTC B1372: Difference Of At Least 75% Between The Ignition 1 Voltage Circuit And The Ipc Battery Positive Voltage Circuit
- DTC B2961: Ignition 1 Input Signal Circuit High
- DTC P0381: Driver State Mismatch
- DTC P0461: No Change In Fuel Level Over Distance
- DTC P0462: Fuel Level Signal Low
- DTC P0463: Fuel Level Signal High
- DTC P0522: EOP Sensor Signal Circuit Voltage Low
- DTC P0523: EOP Sensor Signal Circuit Voltage High
- DTC P0608: Driver State Mismatch
- DTC P0654: Driver State Mismatch
- DTC P2066: No Change In The Secondary Fuel Level Over Distance
- DTC P2067: Secondary Fuel Level Signal Low
- DTC P2068: Secondary Fuel Level Signal High
- Symptoms-Instrument Panel, Gages & Console
- Instrument Cluster Inoperative
- Engine Oil Pressure Gage Inaccurate or Inoperative
- Fuel Gage Inaccurate or Inoperative (Dual Tanks)
- Fuel Gage Inaccurate or Inoperative (Single Tank)
- Fuel Gage Inaccurate Or Inoperative
- Hourmeter Inaccurate Or Inoperative
- Instrument Panel Cluster (IPC) Gages Inoperative
- Odometer Trip/Reset Switch Inoperative
- Transmission Fluid Temperature Gage Inaccurate Or Inoperative
- Change Engine Oil Indicator Always On
- Low Engine Oil Level Indicator Always On
- Water-In-Fuel Lamp Always On
- Driver Information Center (DIC) Switch(es) Inoperative
- Chime Always On
- Chime Inoperative
- Hot & Cold Cupholder Inoperative
- Speedometer and/or Odometer Inaccurate or Inoperative
- Thermoelectric Cooler Inoperative
- Repair Instructions
- Accessory Switch Replacement
- Insulator Replacement - Instrument Panel (I/P)
- Instrument Panel (I/P) Extension Replacement (Pro)
- Knee Bolster Replacement
- Trim Panel Replacement - Instrument Panel (I/P) Upper
- Bezel Replacement - Instrument Panel (I/P) Cluster
- Compartment Replacement - Instrument Panel (I/P)
- Instrument Panel (I/P) Assist Handle Replacement
- Instrument Panel Cluster (IPC) Replacement
- Instrument Cluster Lamp Replacement
- Ashtray Replacement (Non-Console)
- Ashtray Replacement (Console)
- Cupholder Replacement (Luxury)
- Cupholder Replacement (Non-Luxury)
- Cupholder Replacement (Rear)
- Cupholder Replacement (Pro)
- Switch Replacement - Hot and Cold Cupholder
- 12-Volt Power Supply Replacement
- Instrument Panel (I/P) Trim Panel Replacement - Lower
- Instrument Panel (I/P) Assembly Replacement
- Instrument Panel (I/P) Carrier Replacement
- Door Replacement - Console Compartment
- Console Storage Bin Replacement (Expect Pro)
- Console Storage Bin Replacement (Pro)
- Bezel Replacement - Floor Console Extension - Upper
- Console Replacement (Except Pro)
- Console Replacement (Pro)
- Storage Compartment Replacement - Console End Panel
- Bezel Replacement-Floor Console (Non-Luxury Upper)
- Bezel Replacement - Floor Console (Luxury Upper)
- Bezel Replacement - Floor Console (Non-Lux Lower)
- Bracket Replacement-Console Floor
- Center Console End Panel Replacement
- Instrument Panel (I/P) Harness Replacement
- Description and Operation
- Special Tools & Equipment
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.