Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSVOLVO2004V70 L5-2.5L TURBO VIN 59 B5254T2REPAIR AND DIAGNOSISPOWERTRAIN MANAGEMENTTECHNICAL SERVICE BULLETINS
2004 Volvo V70 L5-2.5L Turbo VIN 59 B5254T2
Powertrain Management: Technical Service Bulletins
2004 Volvo V70 L5-2.5L Turbo VIN 59 B5254T2SECTION Technical Service Bulletins
- Recalls
- Customer Interest
- A/T Controls - TCM Update For Various Concerns
- Drivetrain - DEM Software Updates
- Audio/Computer/Controls/Fuel System - AM Radio Static
- Computers/Controls - TCM/DEM Software Updates
- ABS/TCS - DTC's 0076 and 0117
- Engine Controls - Cooling Fan On/DTC 2000 Set
- Engine Control - DTC 250A, 2200/220A/Driveability Issues
- Steering/Suspension - BCM Codes 0121 And 0127
- A/T AW55 - TCM DTC's 010A, 010B, 010C
- A/T - AW55-50 Hard Shifts/Shift Flare
- Engine - Knock/Rattles/Low Power/DTC's Set
- Fuel System - Fuel Filler Neck Loose at Grommet
- Fuel System - Difficult to Fill Fuel Tank
- Fuel System - Starting Problems Parked on a Downhill
- By Symptom
- Customer Interest
- A/T Controls - TCM Update For Various Concerns
- Drivetrain - DEM Software Updates
- Audio/Computer/Controls/Fuel System - AM Radio Static
- Computers/Controls - TCM/DEM Software Updates
- ABS/TCS - DTC's 0076 and 0117
- Engine Controls - Cooling Fan On/DTC 2000 Set
- Engine Control - DTC 250A, 2200/220A/Driveability Issues
- Steering/Suspension - BCM Codes 0121 And 0127
- A/T AW55 - TCM DTC's 010A, 010B, 010C
- A/T - AW55-50 Hard Shifts/Shift Flare
- Engine - Knock/Rattles/Low Power/DTC's Set
- Fuel System - Fuel Filler Neck Loose at Grommet
- Fuel System - Difficult to Fill Fuel Tank
- Fuel System - Starting Problems Parked on a Downhill
- Driveability
- Hard Shifting
- Improper Alignment
- Loose
- No shift/Incorrect gear engagement
- Noise
- Recalls
- Slipping
- Starting problems
- Sticking/Binding
- Won't turn off
- Customer Interest
- All Technical Service Bulletins
- Computers/Controls - Programming And Diagnosis
- A/T Controls - TCM Update For Various Concerns
- Drivetrain - DEM Software Updates
- Audio/Computer/Controls/Fuel System - AM Radio Static
- Emissions - EVAP Leak Detection Diagnostic Improvements
- Recall 220 - Fuel Pump Replacement
- Body Controls - BCM Diagnostic Information
- Fuel System - E10 Petrol Fuel Requirements
- Computers/Controls - Usage of RELOAD Software
- Computers/Controls - TCM/DEM Software Updates
- Computers/Controls - CANbus Network Information
- Engine Controls - Engine Management Software Usage
- ABS/TCS - DTC's 0076 and 0117
- Engine Controls - Software Download Fault Prevention
- Engine Controls - Cooling Fan On/DTC 2000 Set
- Engine Control - DTC 250A, 2200/220A/Driveability Issues
- Steering/Suspension - BCM Codes 0121 And 0127
- A/T AW55 - TCM DTC's 010A, 010B, 010C
- A/T - AW55-50 Hard Shifts/Shift Flare
- Engine - Knock/Rattles/Low Power/DTC's Set
- Fuel System - Fuel Filler Neck Loose at Grommet
- Fuel System - Difficult to Fill Fuel Tank
- Recall 07V226000: Fuel Pressure Sensor Replacement
- Engine - Exchange Cylinder Block Modification
- Fuel System - Starting Problems Parked on a Downhill
- Recall 09V483000: Fuel Pump Replacement
- Fuel System - Fuel Pump Warranty Extension
- Recall 220 - Inspect/Replace Fuel Pump
- Starting System - Ign. Key Won't Turn Past Position 1
- Engine Controls - Reuse Of ECM's
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.