Signal Missing

Signal missing

Checking the connectors for the control module and wheel sensor








- Ignition off
- Check the wheel sensor and brake control module (BCM) connectors. Check for contact resistance and oxidation
- Reinstall the components, reconnect the connectors etc.
- Raise the car so that the relevant wheel is clear of the ground
- Ignition on
- Read off the wheel speed for the relevant wheel.
Spin the relevant wheel and check that the wheel speed is updated.
If the wheel speed is updated, the cause of the fault was loose connections in the connectors for the control module or wheel sensor.

Note! The speed signal will only be active for approximately 20 seconds. Activate the function again if necessary.

Other information
- To disconnect the wheel sensor connector, see Wheel sensor rear, replacing Wheel Sensors, Rear, Replacing
- To disconnect the control module connector, see Connecting the breakout box, brake control module (BCM) Connecting the Breakout Box
- Checking wiring and terminals Checking Wiring And Terminals





Is the wheel speed updated?

Yes - FAULT FOUND

No - Checking wiring and sensors

-------------------------------------------------

Checking wiring and sensors
Checking the power supply
Check the power supply cable between the control module
- terminal #36 (#A36) (left rear)
- terminal #43 (#A43) (right rear).
and terminal #1 on the relevant sensor. Check for an open-circuit. Check for a short-circuit to ground. Check for a short-circuit to supply voltage.

Hint: With the ignition on, the voltage should be approximately 1 V under Ubat measured at the ground terminal.

Checking the signal cable
Check the power supply cable between the control module
- terminal #37 (#A37) (left rear)
- terminal #42 (#A42) (right rear).
and terminal #2 on the relevant sensor. Check for an open-circuit. Check for a short-circuit to ground. Check for a short-circuit to supply voltage.
Checking the function of the sensor
Check the sensor. Ensure that the breakout box is connected, the sensor is connected and the ignition is on. Measure the signal from the sensor. Connect a voltmeter between:
- terminals #36 (#A36) and #37 (#A37) (left front)
- terminals #43 (#A43) and #42 (#A42) (right front).
on the breakout box. The voltage should vary by approximately 1 V when the pulse wheel is rotating. Replace the wheel sensor if the voltage is faulty.
Remedy as necessary.

Other information
- To connect the breakout box, see Connecting the breakout box, brake control module (BCM) Connecting the Breakout Box
- To replace the wheel sensor, see Wheel sensor rear, replacing Wheel Sensors, Rear, Replacing
- For information about signals, see Signal specification, brake control module (BCM) with STC/ TRACS Signal Specification, Brake Control Module (BCM) with STC/ TRACS and Signal specification, brake control module (BCM) with DSTC (dynamic stability and traction control) Signal Specification, Brake Control Module (BCM) with DSTC (Dynamic Stability and Traction Control)
- Checking wiring and terminals Checking Wiring And Terminals









Select Continue when the fault has been remedied.

Continue - Verification

-------------------------------------------------

Verification




Verification

Hint: After carrying out the repair, check that the fault has been remedied.








- Ignition off
- Reinstall the components, reconnect the connectors etc.
- Raise the car so that the relevant wheel is clear of the ground
- Ignition on
- Read off the wheel speed for the relevant wheel.
Spin the relevant wheel and check that the wheel speed is updated.

Note! The speed signal will only be active for approximately 20 seconds. Activate the function again if necessary.





Is the wheel speed updated?

Yes - Verification completed

No - Fault-tracing information

-------------------------------------------------

Fault-tracing information




Information

Fault-tracing information
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.

Do you want to exit fault-tracing?

Yes - Exit Fault-Tracing

No - Attempt New Test

------------------------

Attempt New Test - Checking the connectors for the control module and wheel sensor

-------------------------------------------------