Safety Warning

DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.

SYS.OK|MANUAL.DB● LIVE

HOMESERVICE MANUALSTOYOTA2005MATRIX XR, FWD, STANDARDREPAIR AND DIAGNOSISSUSPENSIONWHEELS & TIRE SYSTEMTIRE PRESSURE WARNING SYSTEM - DIAGNOSTICSTIRE PRESSURE WARNING SYSTEMTEST MODE PROCEDURE

2005 Toyota Matrix XR, FWD, Standard

Test Mode Procedure

2005 Toyota Matrix XR, FWD, StandardSECTION Test Mode Procedure

TEST MODE (USING SST CHECK WIRE)

Make sure that the ignition switch is off.
Using SST, connect terminals TS and CG of the DLC3.
SST 09843-18040
Turn the ignition switch to the ON position.

Fig 1: Connecting Terminals TS And CG Of DLC3 Using SST
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Press the tire pressure warning reset switch.

Check that the tire pressure warning lamp comes on.

HINT:

Unless (d) is performed, the tire pressure warning lamp remains off while in test mode.
When there is a problem with the tire pressure warning system, the tire pressure warning lamp blinks at 0.5 second intervals.

Fig 2: Tire Pressure Warning Lamp Pattern

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

If the lamp output result is not normal, proceed to the problem symptoms table or TS terminal circuit.

PROBLEM SYMPTOMS CHART

Item
PROBLEM SYMPTOMS TABLE
TS AND CG TERMINAL CIRCUIT (W/ VSC)
TS TERMINAL CIRCUIT (W/O VSC)

Turn the ignition switch off.
Remove the SST from the DLC3.
SST 09843-18040
Turn the ignition switch to the ON position.
Check that the tire pressure warning lamp goes off.

Fig 3: Checking Tire Pressure Warning Lamp
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

TEST MODE (USING THE HAND-HELD TESTER)
1. Connect the hand-held tester to the DLC3.
2. Turn the ignition switch to the ON position.
3. Select "SIGNAL CHECK", and proceed to check with the hand-held tester.
  
  Fig 4: Connecting Hand-Held Tester To DLC3
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Press the tire pressure warning reset switch.
5. Check that the tire pressure warning lamp comes on.
  HINT:
  - Unless (d) is performed, the tire pressure warning lamp remains off while in test mode.
  - When there is a problem with the tire pressure warning system, the tire pressure warning lamp blinks at 0.5 second intervals.
  If the lamp output result is not normal, proceed to the problem symptoms table (see PROBLEM SYMPTOMS TABLE ).
6. Turn the ignition switch off.
  
  Fig 5: Tire Pressure Warning Lamp Pattern
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
7. Turn the ignition switch to the ON position.
8. Check that the tire pressure warning lamp goes off.
  
  Fig 6: Checking Tire Pressure Warning Lamp Goes Off
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready Tools Free Quote Check Quote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

• You smell fuel, burning insulation, or see smoke.
• Brakes feel soft, pull hard to one side, or make grinding noises.
• The engine overheats, stalls repeatedly, or misfires under load.
• You are missing required tools, torque specs, or safe lifting equipment.
• You are not confident in the next step or safety outcome.