Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2004MATRIX XR, FWD, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 420 (BODY ELECTRICAL SYSTEMS (TROUBLESHOOTING))TROUBLESHOOTINGPROBLEM SYMPTOMS TABLECOMBINATION METER (WARNING LIGHTS)
2004 Toyota Matrix XR, FWD, Standard
Combination Meter (Warning Lights)
2004 Toyota Matrix XR, FWD, StandardSECTION Combination Meter (Warning Lights)
WARNING: This page is about a different car, the 2002 Toyota Tundra. However, it is still accessible from the selected car via links, so may be relevant.
COMBINATION METER (WARNING LIGHTS)
| Symptom/Suspect Area | Refer To | |
|---|---|---|
| Warning Lights Do Not Light Up (Except Discharge, Open Door And SRS) | ||
| Bulb | N/A | |
| IGN Fuse | FUSES & CIRCUIT BREAKERS | |
| Meter Circuit Plate | CIRCUIT | |
| Wire Harness | WARNING SYSTEMS | |
| Low Oil Pressure Warning Light Does Not Light Up | ||
| Bulb | N/A | |
| Low Oil Pressure Warning Switch | STEP 16 - INSPECT OIL PRESSURE SWITCH CONTINUITY | |
| Meter Circuit Plate | CIRCUIT | |
| Wire Harness | WARNING SYSTEMS | |
| Fuel Level Warning Light Does Not Light Up | ||
| Bulb | N/A | |
| Fuel Level Warning Switch | STEP 11 - INSPECT FUEL LEVEL WARNING SWITCH | |
| Meter Circuit Plate | CIRCUIT | |
| Wire Harness | WARNING SYSTEMS | |
| ABS Warning Light Does Not Light Up | ||
| Bulb | N/A | |
| ABS ECU | ANTI-LOCK . | |
| Wire Harness | WARNING SYSTEMS | |
| Seat Belt Warning Light Does Not Light Up | ||
| Bulb | N/A | |
| Seat Belt Buckle Switch | STEP 23 - BENCH TYPE AND PASSENGER SIDE: INSPECT BUCKLE SWITCH CONTINUITY , STEP 24 - W/O BENCH TYPE (DRIVER SIDE): INSPECT BUCKLE SWITCH CONTINUITY or STEP 25 - SEPARATE TYPE (W/POWER SEAT): INSPECT BUCKLE SWITCH CONTINUITY | |
| Meter Circuit Plate | CIRCUIT | |
| Wire Harness | N/A | |
| Discharge Warning Light Does Not Light Up | ||
| IGN Fuse | FUSES & CIRCUIT BREAKERS | |
| Bulb | N/A | |
| Meter Circuit Plate | CIRCUIT | |
| Wire Harness | WARNING SYSTEMS | |
| Generator | GENERATORS & REGULATORS - 2UZ-FE or GENERATORS & REGULATORS - 5VZ-FE | |
| Brake Warning Light Does Not Light Up | ||
| Bulb | N/A | |
| Parking Brake Switch | STEP 19 - INSPECT PARKING BRAKE SWITCH CONTINUITY | |
| Brake Fluid Level Warning Switch | STEP 18 - INSPECT BRAKE FLUID LEVEL WARNING SWITCH CONTINUITY | |
| Meter Circuit Plate | CIRCUIT | |
| Wire Harness | WARNING SYSTEMS | |
| ATF Temperature Warning Light Does Not Light Up | ||
| Bulb | N/A | |
| ATF Temperature Sensor | DTC P0710: ATF TEMPERATURE SENSOR | |
| ECM | SYSTEM & COMPONENT TESTING - V6 & V8 | |
| Meter Circuit Plate | CIRCUIT | |
| Wire Harness | WARNING SYSTEMS | |
| SRS Warning Light Does Not Light Up | ||
| ECU-B Fuse | FUSES & CIRCUIT BREAKERS | |
| Bulb | N/A | |
| AIRBAG Sensor Assembly | AIR BAG RESTRAINT SYSTEMS | |
| Meter Circuit Plate | CIRCUIT | |
| Wire Harness | WARNING SYSTEMS | |
| Open Door Warning Light Does Not Light Up | ||
| DOME Fuse | FUSES & CIRCUIT BREAKERS | |
| Bulb | N/A | |
| Door Courtesy Switch | STEP 3 - INSPECT DOOR COURTESY SWITCH CONTINUITY | |
| Meter Circuit Plate | CIRCUIT | |
| Wire Harness | WARNING SYSTEMS | |
| Washer Level Warning Light Does Not Light Up | ||
| Bulb | N/A | |
| Washer Fluid Level Warning Switch | STEP 21 - INSPECT WASHER LEVEL SWITCH CONTINUITY | |
| Meter Circuit Plate | CIRCUIT | |
| Wire Harness | WARNING SYSTEMS or WIPER/WASHER | |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.