Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DBβ LIVE
HOMESERVICE MANUALSSUBARU2022IMPREZA BASE, 4D SEDAN, AUTOMATIC CVT TRANSREPAIR AND DIAGNOSISELECTRICALGAUGESINSTRUMENTATION SYSTEM (DIAGNOSTICS)DATA MONITORLIST
2022 Subaru Impreza Base, 4D Sedan, Automatic CVT Trans
Data Monitor: List
2022 Subaru Impreza Base, 4D Sedan, Automatic CVT TransSECTION List
| Item | Contents | Standard/Unit | Note |
|---|---|---|---|
| IG on trip number | Time stamp information | Time | - |
| IG on supply system | Time stamp information | - | - |
| past time after IG on | Time stamp information | ms | - |
| +B voltage | Battery voltage value | 0 - 25 V | - |
| IGN voltage | Ignition power supply voltage value | 0 - 25 V | - |
| Vehicle speed data | Vehicle speed value detected by meter | 0 - 360 km/h | - |
| Engine speed | Engine speed value detected by meter | 0 - 16383 rpm | - |
| Engine coolant water temperature | Engine coolant temperature detected by meter | -40 - 214Β°C | - |
| Fuel level resistance [Ξ©] | Fuel sensor value display | 0 - 511.5 ohm | - |
| Fuel residual quantity indication value [L] | Remaining fuel quantity value display | 0 - 80 L | - |
| Ambient air temperature | External temperature sensor value display | -40 - 80Β°C | - |
| Ambient air temperature | Correction value for displaying ambient temperature | -40 - 80Β°C | - |
| Outside temperature for diagnosis | External temperature sensor value display | -400 - 419.1Β°C | - |
| Ambient rear diff oil temperature | Rear differential oil temperature display | -50 - 200Β°C | - |
| Drivers seat seat-belt wearing state | Driver's seat belt fastened status | Driver's seat belt seated status Driver's seat belt not fastened status |
- |
| Passenger side seat belt state | Passenger's seat belt fastened status | Passenger's seat belt seated status Passenger's seat belt not fastened status |
- |
| Rear side (right) seat belt state | Rear right seat belt fastened status | Rear right seat belt seated status Rear right seat belt not fastened status |
- |
| Rear side (center) seatbelt state | Rear center seat belt fastened status | Rear center seat belt seated status Rear center seat belt not fastened status |
- |
| Rear side (left) seat belt state | Rear left seat belt fastened status | Rear left seat belt seated status Rear left seat belt not fastened status |
- |
| ODO/TRIP switch input state | Input condition of ODO/TRIP switch is displayed | Switch OFF status Switch ON status |
- |
| TFT display reshuffling switch input state | Input condition of TFT display change switch is displayed | Switch OFF status Shift Up Switch ON status Shift Down Switch ON status i/SET Switch ON status Input indefinite status |
- |
| Illumination control switch input state | Input condition of illumination control switch is displayed | 0 - 100 % | - |
| Bright switch input state | Input condition of bright switch is displayed | Bright OFF status Bright ON status |
- |
| Si-DRIVE switch input state | Input condition of SI-DRIVE switch is displayed | Switch OFF status [S/I] Switch input [S#/I] Switch input [I] Switch input [S] Switch input [S#] Switch input Input unidentified status |
- |
| X mode switch input state | Input condition of X mode switch is displayed | Switch OFF status Switch ON status |
- |
| LO switch input state | Input condition of dual range LO switch is displayed | Switch OFF status Switch ON status |
- |
| idling stop OFF switch input state | Input condition of Auto Start Stop OFF switch is displayed | Switch Open State Switch GND State |
- |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.