Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSUBARU2014LEGACY 2.5I, AUTOMATIC CVT TRANSREPAIR AND DIAGNOSISBRAKESPARKING BRAKE SYSTEMPARKING BRAKE SYSTEM (DIAGNOSTICS)SUBARU SELECT MONITOROPERATIONFREEZE FRAME DATA
2014 Subaru Legacy 2.5i, Automatic CVT Trans
Freeze Frame Data
2014 Subaru Legacy 2.5i, Automatic CVT TransSECTION Freeze Frame Data
NOTE:
- Data stored at the time of trouble occurrence is shown on display.
- Each time a trouble occurs, the latest information is stored in the Freeze Frame Data in memory.
| Display | Contents to be displayed |
|---|---|
| FR Wheel Speed | Wheel speed detected by front ABS wheel speed sensor RH is displayed. |
| FL Wheel Speed | Wheel speed detected by front ABS wheel speed sensor LH is displayed. |
| RR Wheel Speed | Wheel speed detected by rear ABS wheel speed sensor RH is displayed. |
| RL Wheel Speed | Wheel speed detected by rear ABS wheel speed sensor LH is displayed. |
| Power Supply Voltage | The voltage supplied to the electronic parking brake control module is displayed. |
| Engine Speed | Engine speed is displayed. |
| Accel. Opening Angle | Acceleration opening is displayed. |
| Reverse Signal | Input condition of reverse signal is displayed. (When reverse: ON) |
| Brake Switch | Input condition of brake pedal signal is displayed. (When depressed: ON) |
| Force Sensor | The tension detected by the force sensor in the actuator is displayed. |
| Stroke Sensor | The parking brake cable stroke amount detected by the stroke sensor in the actuator is displayed. |
| Clutch stroke sensor | The pedal stroke amount detected by the clutch stroke sensor is displayed. |
| Clutch engagement point | Clutch engagement position is displayed. |
| Actuator Inner Temperature (Primary) | Actuator inner temperature (PRY) is displayed. |
| Actuator Inner Temperature (Secondary) | Actuator inner temperature (SEC) is displayed. |
| Incline | Incline of the vehicle is displayed. |
| Engine Torque | Engine torque is displayed. |
| Manual Parking Operation | Parking brake operation condition is displayed. (At manual parking operation: 1) |
| Auto Parking Operation | Parking brake operation condition is displayed. (At automatic parking operation: 1) |
| Parking Operation when driving | Parking brake operation condition is displayed. (At parking operation when driving: 1) |
| Parking Cancel | Parking brake operation condition is displayed. (At parking cancel: 1) |
| Hill hold lamp | Hill hold indicator control condition is displayed. (When illuminating: ON) |
| Ignition Signal | Input condition of ignition signal is displayed. |
| Neutral Signal | Input condition of neutral signal is displayed. (When neutral: ON) |
| Engine idle flag | Engine speed condition is displayed. (When idling: ON) |
| Door Signal | Input condition of door (4 locations) open/close signal is displayed. (When at least one door is open: OPEN) |
| Driver Seat Belt Signal | Input condition of driver's seatbelt signal is displayed. |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.