SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSUBARU2014IMPREZA SPORT LIMITEDREPAIR AND DIAGNOSISACCESSORIES & EQUIPMENTCOMMUNICATION DEVICESBODY CONTROL SYSTEM (DIAGNOSTICS)REGISTRATION BODY INTEGRATED UNITOPERATIONDESTINATION SETTING
2014 Subaru Impreza Sport Limited

Destination Setting

2014 Subaru Impreza Sport LimitedSECTION Destination Setting
NOTE: For the vehicle requiring the destination setting, if the destination setting is not finished, display can not be shifted into customizing screen.
Step Check Yes No
1 CONFIRM CURRENT SETTING. 
Always perform confirmation of current setting before replacing the module.
Record the contents of the "Destination Setting".
NOTE: Refer to the "Read Current Data" and "CONFIRMATION OF CURRENT SETTING" to confirm the current setting. < Ref. to CONFIRM CURRENT SETTING , OPERATION, Registration Body Integrated Unit.> < Ref. to OPERATION , Read Current Data.>
 Is the current setting recorded? Go to step 2  . Confirm the current setting. Go to step 1  .
2 CONFIRM DESTINATION SETTING. 
  1. Connect the Subaru Select Monitor, and run the application.
  2. On «Main Menu» display, select {Each System Check}.
  3. On the «System Selection Menu» display, select {Integ. unit mode}.
  4. On «Integ. unit mode» display, select {Work Support}.
  5. On «Work Support» display, select {Unit customizing}.
  6. The vehicle destination screen is displayed.
 Is the vehicle destination setting screen displayed? Go to step 3  . Go to step 4  .
3 CONFIRM DESTINATION SETTING. 
Confirm the screen displayed on Subaru Select Monitor and the actual vehicle destination.		 Is it necessary to change the destination setting? Select [Yes]. Go to step 4  . Select [No]. Go to step 5.
4 ENTER DESTINATION CODE. 
Enter the appropriate code in the screen.
JPN: JP00
KA, KC: KA00
KS: KS00
U4, U5, U6, C6 and C0, C5 (with keyless access): U400
C0, C5 (without keyless access): C000
EK, ER: EK00
Other than above: EC00		 Is the appropriate code entered? Select [Yes]. Go to step 5  . Enter the destination code. Go to step 5  .
5 REGISTER VEHICLE EQUIPMENTS. 
Customizing screen is displayed.
NOTE: Match the each item setting of body integrated unit registration item list with the vehicle equipments.
 Do all setting contents match with the vehicle equipment specification? Go to step 6  . Change the items until each content setting match with the vehicle equipments specification. Go to step 6  .
6 CONFIRM MARKET MODE. 
  1. Customizing screen, select the {Factory initial setting} to change the setting from "Factory" mode to "Market" mode.
  2. Turn the ignition switch to OFF.
    NOTE: When the setting is changed from "Factory" mode to "Market" mode, turning the ignition switch from ON → OFF confirms the setting.
  3. Turn the ignition switch to ON, and check the contents of settings.
 Is the mode changed to "Market" mode? Go to step 7  . Perform the destination setting from the first step. Go to step 1.
7 CONFIRM MARKET MODE. 
Check the following.
Make sure that the "Destination Setting" in the current data display is the same as the one you confirmed in step 1.		 Is the display the same as indicated? Registration of body integrated unit is finished. It is possible that harness malfunction may occur. Perform the diagnosis.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.