SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSUBARU2010OUTBACK R PREMIUMREPAIR AND DIAGNOSISACCESSORIES & EQUIPMENTCOMMUNICATION DEVICESBODY CONTROL SYSTEM (DIAGNOSTICS)USER CUSTOMIZINGOPERATION
2010 Subaru Outback R Premium

User Customizing: Operation

2010 Subaru Outback R PremiumSECTION Operation
  1. On «Main Menu» display, select {Each System Check}.
  2. On «System Selection Menu» display, select {Integ. unit mode}.
  3. On «Integ. unit mode failure diag» display, select {ECM customizing}.
  4. Change the setting with UP/DOWN key and set with the [OK] key. List of User Customizing item
    INITIAL SETTING VALUE REFERENCE

    Data Initial setting value Customize setting Remarks
    Off delay time Long   Delay time below can be selected by setting.
    OFF 0 seconds
    Short 10 seconds
    Normal 20 seconds
    Long 30 seconds
    Auto Light Sensitivity Adjustment Standard 1st Slow response
    2nd Standard
    3rd Quick response
    4th Fairly quick response
    Rr defogger op. mode Normal Normal Automatically stops in 15 minutes after switch is turned to ON.
    Continuous Repeats active condition for 15 minutes and inactive condition for 2 minutes until switch is turned to OFF.
    Wiper deicer op. mode Normal Normal Automatically stops in 15 minutes after switch is turned to ON.
    Continuous Repeats active condition for 15 minutes and inactive condition for 2 minutes until switch is turned to OFF.
    Security Alarm Setup OFF ON Security alarm (hazard, horn or siren) in active condition
    OFF Security alarm in inactive condition
    Impact Sensor Setup OFF ON Workable when Impact Sensor Setup is set to "ON" Impact sensor function becomes activated.
    OFF Impact sensor in inactive condition (Set to "OFF" in models without sensors.)
    Alarm delay setup ON   After the keyless lock operation, the alarm monitor starts after the following delay time has passed.
    ON Delay time is 30 seconds.
    OFF Delay time is 0 seconds.
    Lockout prevention ON ON Lockout prevention in active condition. (The function does not operate if safety knob is locked by hand.)
    OFF Lockout prevention in inactive condition
    Impact sensor (OP) OFF ON Vehicle is controlled in impact sensor equipped mode. (Make sure to set to "OFF" for models without the impact sensor. When "ON", hazard, horn or siren become activated by keyless lock (alarm monitor start).)
    OFF Vehicle is controlled in no impact sensor mode.
    Answer-back buzzer setup ON ON When lock/unlock is selected by keyless entry system operation, buzzer operates.
    OFF When lock/unlock is selected by keyless entry system operation, buzzer does not operate.
    Hazard answer-back setup ON ON When lock/unlock is selected by keyless entry system operation, hazard blinks.
    OFF When lock/unlock is selected by keyless entry system operation, hazard does not interlock.
    Initial keyless setting - -  
    Execution  
    Initial button setting - -  
    Execution  
    Passive Alarm ON ON  
    OFF  
    Door open warning ON ON  
    OFF  
    Dome Light Alarm Setting ON ON Room light illuminates interlocking with alarm.
    OFF Room light does not illuminate interlocking with alarm.
    Belt Warning Switch ON ON Belt warning buzzer beeps.
    OFF Belt warning buzzer stops.
    Auto A/C ECU Setting - ON Diagnoses with auto A/C ECU.
    OFF Diagnoses without auto A/C ECU.
    Line Navigation Setting - ON Diagnoses with line navigation.
    OFF Diagnoses without line navigation.
    wiperdeicer - ON Wiper deicer control is performed.
    OFF Wiper deicer control is not performed.
    Sedan/Wagon Setting - Sedan Body control is performed by Sedan.
    Wagon Body control is performed by Wagon.
    MT/AT Setting - MT Body control is performed by MT.
    AT Body control is performed by AT.
    6MT Setting - 6MT Body control is performed by 6MT.
    Other than 6MT Body control is performed by other than 6MT.
    Seat Memory Setting - ON Performs control when seat memory is ON.
    OFF Performs control when seat memory is OFF.
    Factory or Market setting Market Market Customize setting is reset when mode is switched from Market to Factory.
    Factory
  5. After setting, make sure that the setting changed in the {Current Data Display & Save} is same as vehicle equipment.
    CAUTION:
    • The above settings must match the actual vehicle equipment.
    • Do not change settings except for setting above while setting the functions.
    • Be sure not to change Factory or Market setting except when installing a new body integrated unit.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.