Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSUBARU2007OUTBACK LIMITED, 4D SEDAN, STANDARDREPAIR AND DIAGNOSIS (SINGLE PAGE)BRAKESANTI-LOCK BRAKESVEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS)
2007 Subaru Outback Limited, 4D Sedan, Standard
Vehicle Dynamics Control (VDC) (Diagnostics)
2007 Subaru Outback Limited, 4D Sedan, StandardSECTION Vehicle Dynamics Control (VDC) (Diagnostics)
- Basic Diagnostic Procedure
- Check List for Interview
- General Description
- Brake Pad And Rotor
- Electrical Component Location
- Control Module I/O Signal
- Subaru Select Monitor
- Read Diagnostic Trouble Code (DTC)
- Inspection Mode
- Clear Memory Mode
- Warning Light Illumination Pattern
- List of Diagnostic Trouble Code (DTC)
- Diagnostic Procedure with Diagnostic Trouble Code (DTC)
- DTC C0021 Front Right Abs Sensor Circuit Open Or Short
- DTC C0023 Front Left Abs Sensor Circuit Open Or Short
- DTC C0025 Rear Right Abs Sensor Circuit Open Or Short
- DTC C0027 Rear Left Abs Sensor Circuit Open Or Short
- TC C0022 Front Right Abs Sensor Signal
- TC C0024 Front Left Abs Sensor Signal
- TC C0026 Rear Right Abs Sensor Signal
- DTC C0028 Rear Left Abs Sensor Signal
- DTC C0029 Any Of Wheel Sensors Signal
- DTC C0031 Fr Hold Valve Malfunction
- DTC C0032 Fr Pressure Reducing Valve Malfunction
- DTC C0033 Fl Hold Valve Malfunction
- DTC C0034 Fl Pressure Reducing Valve Malfunction
- DTC C0035 RR Hold Valve Malfunction
- DTC C0036 RR Pressure Reducing Valve Malfunction
- DTC C0037 RL Hold Valve Malfunction
- DTC C0038 RL Pressure Reducing Valve Malfunction
- DTC C0039 Any One Of Four Solenoid Valves
- DTC C0061 Normal Opening Valve 1 Malfunction
- DTC C0062 Normal Opening Valve 2 Malfunction
- DTC C0063 Normal Closing Valve 1 Malfunction
- DTC C0064 Normal Closing Valve 2 Malfunction
- DTC C0041 ECM
- DTC C0041 Parameter Selection Error
- DTC C0042 Power Supply Voltage Failure
- DTC C0044 TCM Communication Circuit
- DTC C0045 Incorrect VDC Control Module Specifications
- DTC C0045 TCM Malfunction
- DTC C0047 Can Communication
- DTC C0051 Valve Relay
- DTC C0052 Motor And Motor Relay Off Failure
- DTC C0052 Motor And Motor Relay On Failure
- DTC C0052 Motor Malfunction
- DTC C0054 BLS Circuit Open
- DTC C0054 BLS On Malfunction
- DTC C0054 BLS Off Malfunction
- DTC C0057 ECM Communication Circuit
- DTC C0057 ECM Control System
- DTC C0071 Steering Angle Sensor Offset Is Too Big
- DTC C0071 Change Range Of Steering Angle Sensor Is Too Big
- DTC C0071 Steering Angle Sensor Malfunction
- DTC C0072 Abnormal Yaw Rate Sensor Output
- DTC C0072 Voltage Inputted To Yaw Rate Sensor Exceeds Specification
- DTC C0072 Abnormal Yaw Rate Sensor Reference Voltage
- DTC C0072 Change Range Of Yaw Rate Sensor Signal Is Too Big
- DTC C0073 Lateral G Sensor Communication
- DTC C0072 Yaw Rate Sensor Communication
- DTC C0073 Lateral G Sensor Offset Is Too Big
- DTC C0073 Abnormal Lateral G Sensor Output
- DTC C0073 Excessive Lateral G Sensor Signal
- DTC C0074 Pressure Sensor
- DTC C0081 System Failure
- General Diagnostic Table
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.