Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSATURN2006RELAY 3.5 L, FWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 171 (COMPUTER/INTEGRATING SYSTEMS)
2006 Saturn Relay 3.5 L, FWD
Section 171 (Computer/Integrating Systems)
2006 Saturn Relay 3.5 L, FWDSECTION Section 171 (Computer/Integrating Systems)
WARNING: This page is about a different car, the 2006 Chevrolet Monte Carlo and 2006 Chevrolet Impala. However, it is still accessible from the selected car via links, so may be relevant.
- Specifications
- Schematic and Routing Diagrams
- Component Locator
- Diagnostic Information and Procedures
- Diagnostic Code Index
- Diagnostic Starting Point - Computer/Integrating Systems
- Scan Tool Data List
- Scan Tool Data Definitions
- DTC B0005
- DTC B1000
- DTC B1001
- DTC B1016
- DTC B1370
- DTC Descriptor
- Diagnostic Fault Information
- Typical Scan Tool Data
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Conditions for Clearing the DTC
- Diagnostic Aids
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Component Testing
- Repair Procedures
- DTC B1380
- DTC Descriptor
- Diagnostic Fault Information
- Typical Scan Tool Data
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Conditions for Clearing the DTC
- Diagnostic Aids
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Component Testing
- Repair Procedures
- DTC B1428
- DTC B1440
- DTC Descriptor
- Diagnostic Fault Information
- Typical Scan Tool Data
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Diagnostic Aids
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Component Testing
- Repair Procedures
- DTC B1441
- DTC Descriptor
- Diagnostic Fault Information
- Typical Scan Tool Data
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Diagnostic Aids
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Component Testing
- Repair Procedures
- DTC B1475
- DTC U0073
- DTC U0100 - U0299
- DTC U1814
- DTC Descriptor
- Diagnostic Fault Information
- Typical Scan Tool Data
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Diagnostic Aids
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Repair Procedures
- DTC U2099
- DTC Descriptor
- Diagnostic Fault Information
- Typical Scan Tool Data
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Diagnostic Aids
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Repair Procedures
- Symptoms - Computer/Integrating Systems
- Scan Tool Does Not Power Up
- Scan Tool Does Not Communicate with High Speed GMLAN Device
- Scan Tool Does Not Communicate with Low Speed GMLAN Device
- Power Mode Mismatch
- Retained Accessory Power (RAP) Malfunction
- Control Module References
- Data Link References
- Repair Instructions
- Description and Operation
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.