SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSPONTIAC1997GRAND PRIX GTP, 4D SEDANREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTANTI-THEFT SYSTEMSKEYLESS ENTRY SYSTEM - REMOTESYSTEM TESTINGKEYLESS ENTRY SYSTEM INOPERATIVE
1997 Pontiac Grand Prix GTP, 4D Sedan

Keyless Entry System Inoperative

1997 Pontiac Grand Prix GTP, 4D SedanSECTION Keyless Entry System Inoperative
  1. Resynchronize all transmitters. See TRANSMITTER RESYNCHRONIZATION  under PROGRAMMING - PROCEDURES. If door locks cycle while resynchronizing transmitters, go to next step. If door locks do not cycle while resynchronizing transmitter, go to step 3).
  2. Test system using RKE transmitters. If RKE system operates, system okay. Verify system operation. If RKE system does not operate, go to step 4).
  3. Check voltage of RKE transmitter batteries. If voltage is between 3-3.5 volts, go to step 5). If voltage is not between 3-3.5 volts, go to step 6).
  4. Operate door locks using door lock switches. If doors lock operate normally, go to step 7). If door locks do not operate normally, see POWER DOOR LOCKS article.
  5. Reprogram all transmitters. See TRANSMITTER PROGRAMMING  under PROGRAMMING - PROCEDURES. Test system using RKE transmitter. If RKE system operates normally, system okay. Verify system operation. If RKE system does not operate normally, go to step 8).
  6. Replace transmitter batteries. Resynchronize transmitter. See TRANSMITTER RESYNCHRONIZATION  . If door locks cycle during resynchronization of transmitters, go to step 2). If door locks did not cycle during resynchronization of transmitters, go to step 8).
  7. Reprogram all transmitters. See TRANSMITTER PROGRAMMING0  under PROGRAMMING - PROCEDURES. Using RKE transmitter, test system operation. If keyless entry system works properly, system okay. If keyless entry system does not work properly, go to step 9).
  8. Program known good transmitter. See TRANSMITTER PROGRAMMING  under PROGRAMMING - PROCEDURES. Using RKE transmitter, test system operation. If keyless entry system works properly, go to step 9). If keyless entry system does not work properly, go to step 10).
  9. Replace defective RKE transmitter. Verify system operation.
  10. Disconnect remote control door lock receiver (RCDLR) Black 16-pin connector. Using test light, backprobe RCDLR connector Orange wire terminal and Black wire terminal. If test light illuminates, go to step 11). If test light does not illuminate, go to step 12).
  11. Check for poor connection at RCDLR. If okay, replace RCDLR. Verify system operation.
  12. Using test light, backprobe between ground and RCDLR connector Orange wire terminal. If test light illuminates, go to step 13). If test light does not illuminate, go to step 14).
  13. Repair poor connection or open in Black wire between RCDLR and ground. Verify system operation.
  14. Repair poor connection or open in Orange wire between RCDLR and ground. Verify system operation.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.