DTC Inspection Priority Chart

2015 Nissan-Datsun Juke SL, 4WDSECTION DTC Inspection Priority Chart
WARNING: This page is about a different variant/trim than selected.

If some DTCs are displayed at the same time, perform inspections one by one based on the following priority chart.

Priority Detected items (DTC)
1
  • U0101 U0122 U1001 CAN communication line
  • P0096 P0097 P0098 Intake air temperature sensor 2
  • P0101 P0102 P0103 Mass air flow sensor
  • P0111 P0112 P0113 P0127 Intake air temperature sensor 1
  • P0116 P0117 P0118 P0125 Engine coolant temperature sensor
  • P011C Intake air temperature sensor 2
  • P0122 P0123 P0222 P0223 P1225 P1226 P2135 Throttle position sensor
  • P0128 Thermostat function
  • P0181 P0182 P0183 Fuel tank temperature sensor
  • P0190 P0192 P0193 P119A P119B P119C Fuel rail pressure sensor
  • P0196 P0197 P0198 Engine oil temperature sensor
  • P0235 Turbocharger boost sensor
  • P0327 P0328 Knock sensor
  • P0335 Crankshaft position sensor (POS)
  • P0340 Camshaft position sensor (PHASE)
  • P0460 P0461 P0462 P0463 Fuel level sensor
  • P0500 P0501 P2159 P2162 Vehicle speed sensor
  • P0520 Engine oil pressure sensor
  • P0603 P0604 P0605 P0606 P0607 P060A P060B P0611 P062B ECM
  • P0643 Sensor power supply
  • P0705 Transmission range switch
  • P0850 Park/neutral position (PNP) switch
  • P1197 Out of gas*
  • P1550 P1551 P1552 P1553 P1554 Battery current sensor
  • P1556 P1557 Batter temperature sensor
  • P158A ECM
  • P159A P159B P159C P159D G sensor
  • P1610 - P1612 NATS
  • P1650 P1651 P1652 Starter motor relay
  • P2122 P2123 P2127 P2128 P2138 Accelerator pedal position sensor
2
  • P0030 P0031 P0032 Air fuel ratio (A/F) sensor 1 heater
  • P0037 P0038 Heated oxygen sensor 2 heater
  • P0045 P0047 P0048 Turbocharger boost control solenoid valve
  • P0075 Intake valve timing control solenoid valve
  • P0078 Exhaust valve timing control solenoid valve
  • P0130 P0131 P0132 P014C P014D P015A P015B P2096 P2097 Air fuel ratio (A/F) sensor 1
  • P0137 P0138 P0139 Heated oxygen sensor 2
  • P0237 P0238 Turbocharger boost sensor
  • P0441 EVAP control system purge flow monitoring
  • P0443 P0444 P0445 EVAP canister purge volume control solenoid valve
  • P0447 P0448 EVAP canister vent control valve
  • P0451 P0452 P0453 EVAP control system pressure sensor
  • P0710 P0715 P0720 P0740 P0744 P0745 P0746 P0776 P0778 P0840 P1740 P1777 P1778 CVT related sensors, solenoid valves and switches
  • P1078 Exhaust valve timing position sensor
  • P1217 Engine over temperature (OVERHEAT)
  • P1451 Pressure sensor
  • P1805 Brake switch
  • P2100 P2103 Throttle control motor relay
  • P2101 Electric throttle control function
  • P2118 Throttle control motor
3
  • P0011 Intake valve timing control
  • P0014 Exhaust valve timing control
  • P0087 P0088 P0090 FRP control system
  • P0171 P0172 Fuel injection system function
  • P0201 - P0204 Injector
  • P0234 P2263 Turbocharger system
  • P0300 - P0304 Misfire
  • P0420 Three way catalyst function
  • P0456 EVAP control system (very small leak)
  • P0506 P0507 Idle speed control system
  • P050A P050E P1423 P1424 Cold start control
  • P0524 Engine oil pressure
  • P1148 Closed loop control
  • P1212 TCS communication line
  • P1564 ASCD steering switch
  • P1572 ASCD brake switch
  • P1574 ASCD vehicle speed sensor
  • P2119 Electric throttle control actuator
NOTE:

* : If "P1197" is displayed with other DTC in priority 1, perform trouble diagnosis for "P1197" first.

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.