SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSNISSAN-DATSUN2013JUKE SL, 4WDREPAIR AND DIAGNOSISTRANSMISSIONAUTOMATIC TRANSMISSIONBASIC INSPECTIONADDITIONAL SERVICE WHEN REPLACING CONTROL VALVE OR TRANSAXLE ASSEMBLYPROCEDURE
2013 Nissan-Datsun Juke SL, 4WD

Additional Service When Replacing Control Valve Or Transaxle Assembly: Procedure

2013 Nissan-Datsun Juke SL, 4WDSECTION Procedure
CAUTION: Immediately after TCM is replaced or after control valve or transaxle assembly is replaced (after TCM initialization is complete), self-diagnosis result of "P1701", "P1709" may be displayed. In this case, erase self-diagnosis result using CONSULT. After erasing self-diagnosis result, perform DTC "P1701", "P1709" reproduction procedure and check that malfunction is not detected. Refer to "DTC LOGIC " (P1701), "DTC LOGIC " (P1709).
  1. PREPARATION BEFORE WORK 

    With CONSULT 

    1. Start the engine.
      CAUTION: Never drive the vehicle.
    2. Select "Data Monitor" in "TRANSMISSION".
    3. Select "ATFTEMP COUNT".

      Is "ATFTEMP COUNT" 47 [equivalent to 20°C (68°F)] or more? 

      YES: GO TO 2.

      NO:

      1. Warm up the transaxle assembly until "ATFTEMP COUNT" reaches "47" [equivalent to 20°C (68°F)] or more.
      2. GO TO 2.
  2. PERFORM TCM INITIALIZATION 

    With CONSULT 

    1. Turn ignition switch OFF.
    2. Turn ignition switch ON.
      CAUTION: Never start the engine.
    3. Select "Self Diagnostic Results" in "TRANSMISSION".
    4. Shift selector lever to "R" position.
    5. Depress slightly the accelerator pedal (Pedal angle: 2.0/8) while depressing the brake pedal.
    6. Select "Erase" with step  5.
    7. Release brake pedal and accelerator pedal.
    8. Select "CALIB DATA" in "TRANSMISSION".
    9. Check that "CALIB DATA" value is as shown as in the following table.
      Item name Display value
      UNIT CLB ID 1 00
      UNIT CLB ID 2 00
      UNIT CLB ID 3 00
      UNIT CLB ID 4 00
      UNIT CLB ID 5 00
      UNIT CLB ID 6 00

      Is "CALIB DATA" value it? 

      YES: GO TO 3.

      NO: GO TO  1.

  3. LOAD CALIBRATION DATA 
    1. Shift selector lever to "P" position.
    2. Check that "P" is displayed on shift position indicator on combination meter.
      NOTE: It indicates approximately 1 - 2 seconds after shifting the selector lever to "P" position.

      Does shift position indicator display "P"? 

      YES: GO TO  5.

      NO: GO TO 4.

  4. DETECT MALFUNCTIONING ITEM 

    Check the following items:

    • Harness between the TCM and the ROM assembly inside the transaxle assembly is open or shorted.
    • Disconnected, loose, bent, collapsed, or otherwise abnormal connector housing terminals
    • Power supply and ground of TCM. (Refer to "DIAGNOSIS PROCEDURE ".)

      Is the inspection result normal? 

      YES: GO TO  1.

      NO: Repair or replace the malfunctioning parts.

  5. STORE CALIBRATION DATA 
    1. Turn ignition switch OFF and wait for 5 seconds.
    2. Turn ignition switch ON.

      Does the shift position indicator display "P" at the same time when turning ON the ignition switch? 

      YES: GO TO 6.

      NO: Check harness between battery and TCM harness connector terminal. Refer to "DIAGNOSIS PROCEDURE ".

  6. ERASE CVT FLUID DEGRADATION LEVEL DATA 

    With CONSULT 

    1. Select "WORK SUPPORT" in "TRANSMISSION".
    2. Select "CONFORM CVTF DETERIORTN".
    3. Touch "Clear".

      : WORK END

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.