Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMITSUBISHI2012OUTLANDER ESREPAIR AND DIAGNOSISMAINTENANCEPROCEDURESGENERAL INFORMATION
2012 Mitsubishi Outlander ES
General Information
2012 Mitsubishi Outlander ESSECTION General Information
- How To Use This Information
- Troubleshooting Guidelines
- How To Use Troubleshooting/Inspection Service Points
- Troubleshooting Contents
- Notes
- 1. Standard Flow Of Diagnostic Troubleshooting
- 2. System Operation And Symptom Verification Tests
- 3. Diagnostic Function
- 4. Diagnostic Trouble Code Chart
- 5. Symptom Chart
- 6. Diagnostic Trouble Code Procedures
- 7. Symptom Procedures
- 8. Service Data Reference Table
- 9. Check At Ecu Terminals
- 10. Inspection Procedures Using An Oscilloscope
- How To Use The Inspection Procedures
- Connector Measurement Service Points
- Connector Inspection Service Points
- How To Cope With Intermittent Malfunctions
- How To Treat Past Trouble
- Inspection Service Points For A Blown Fuse
- Troubleshooting Contents
- Vehicle Identification
- General Data And Specifications
- Precautions Before Service
- Cautions For Working In Engine Compartment
- Supplemental Restraint System (SRS)
- Scan Tool (Multi Use Tester {M.U.T.-III} Sub Assembly)
- How To Perform Vehicle Identification Number (VIN) Writing
- Coding List
- Initialization Procedure For Learning Value In MFI Engine
- Engine Idling Learning Procedure
- Timing Chain Learned Value Reset < 2.4L Engine >
- Battery Current Sensor Calibration < 2.4L Engine >
- Servicing Electrical System
- How To Shift Lock Forced Release
- Vehicle Washing
- Application Of Anti-Corrosion Agents And Undercoats
- Form-In-Place Gasket (FIPG)
- Tightening Torque
- Lubrication And Maintenance
- Recommended Lubricants And Lubricant Capacities Table
- Scheduled Maintenance Table
- Maintenance Service
- 1. Fuel System (Tank, Pipe Line And Connection, And Fuel Tank Filler Tube Cap) (Check For Leaks)
- 2. Fuel Hoses (Check Condition)
- 3. Air Cleaner Element (Replace)
- 4. Evaporative Emission Control System (Except Evaporative Emission Canister) (Check For Leaks And Clogging)
- 5. Spark Plugs (Replace)
- 6. Intake And Exhaust Valve Clearance (Inspect And Adjust)
- 7. Timing Belt (Replace)
- 8. Drive Belt (For Generator, Power Steering Oil Pump) (Check Condition)
- 9. Exhaust System (Connections Portion Of Muffler, Muffler Pipes And Converter Heat Shields) (Check And Service As Required)
- 10. Engine Oil (Change)
- 11. Engine Oil Filter (Replace)
- 12. Transmission Fluid (CVT Fluid) (Check Fluid Level And Condition/Change)
- 13. Transfer Oil (Check Oil Level And Condition/Change)
- 14. Engine Coolant
- 15. Coolant Hoses (Radiator Hose, Heater Hose) (Inspect)
- 16. Disk Brake Pads, Rotors (Inspect For Wear)
- 17. Brake Hoses (Check For Deterioration Or Leaks)
- 18. Ball Joint And Steering Linkage Seals (Inspect For Grease Leaks And Damage)
- 19. Drive Shaft Boots (Inspect For Grease Leaks And Damage)
- 20. Suspension System (Inspect For Looseness And Damage)
- 21. Rear Axle Oil (Check Oil Level)
- 22. Tires (Rotate)
- 23. Air Filter (Replace)
- Main Sealant And Adhesive Table
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.