Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMERCURY2000SABLE V6-3.0L DOHC VIN SREPAIR AND DIAGNOSISRESTRAINTS AND SAFETY SYSTEMSAIR BAG SYSTEMSAIR BAG CONTROL MODULESERVICE AND REPAIRPROCEDURESSTRIPPED NUT, RESTRAINTS CONTROL MODULE (RCM) AND SIDE SENSOR
2000 Mercury Sable V6-3.0L DOHC VIN S
Stripped Nut, Restraints Control Module (RCM) and Side Sensor
2000 Mercury Sable V6-3.0L DOHC VIN SSECTION Stripped Nut, Restraints Control Module (RCM) and Side Sensor
WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE REPAIRING OR REPLACING ANY FRONT OR SIDE AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) COMPONENTS AND BEFORE SERVICING, REPLACING, ADJUSTING OR STRIKING COMPONENTS NEAR THE FRONT OR SIDE AIR BAG SENSORS, SUCH AS DOORS, INSTRUMENT PANEL, CONSOLE, DOOR LATCHES, STRIKERS, SEATS AND HOOD LATCHES.
DETERMINE LOCATION OF THE FRONT AIR BAG SENSORS.
THE SIDE AIR BAG SENSORS ARE LOCATED AT OR NEAR THE BASE OF THE B-PILLAR.
TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY GROUND CABLE AND WAIT AT LEAST ONE MINUTE. BE SURE TO DISCONNECT AUXILIARY BATTERIES AND POWER SUPPLIES (IF EQUIPPED).
1. Obtain an 8 mm (0.32 in) grounding screw.
2. Drill out the internal threads of the stripped-out weld nut to 7.37 mm (0.29 in) using a letter size drill bit.
3. Position the crash sensor to the vehicle.
4. Install the 8 mm (0.32 in) grounding screw into the drilled-out weld nut.
5. Install the remaining attaching screws.
6. Tighten the attaching screws to specification.
DETERMINE LOCATION OF THE FRONT AIR BAG SENSORS.
THE SIDE AIR BAG SENSORS ARE LOCATED AT OR NEAR THE BASE OF THE B-PILLAR.
TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY GROUND CABLE AND WAIT AT LEAST ONE MINUTE. BE SURE TO DISCONNECT AUXILIARY BATTERIES AND POWER SUPPLIES (IF EQUIPPED).
1. Obtain an 8 mm (0.32 in) grounding screw.
2. Drill out the internal threads of the stripped-out weld nut to 7.37 mm (0.29 in) using a letter size drill bit.
3. Position the crash sensor to the vehicle.
4. Install the 8 mm (0.32 in) grounding screw into the drilled-out weld nut.
5. Install the remaining attaching screws.
6. Tighten the attaching screws to specification.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.