Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Lexus LS 460LFACTORY OEM SERVICE PROCEDURE
Specifications Index
LS460L SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front Hub Bolts | 65 N.m (663 kgf.cm 48 ft.lbs) | ||
| Rear Axle Nut | 290 N.m (2,957 kgf.cm 214 ft.lbs) | ||
| Battery | NA | ||
| Brakes | |||
| Bleeding Sequence | BRAKE FLUID | ||
| Disc Brakes | SERVICE DATA | ||
| Drum Brakes | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Belt Routing | DRIVE BELT | ||
| Belt Tensioning | Belt Tensioned By Auto Belt Tensioner INSTALLATION |
||
| Engine Cooling | |||
| General Service Specifications | SERVICE DATA | ||
| Radiator Cap Pressure | |||
| Standard Value (New Cap) | 93.3-122.7 kPa (0.95-1.25 kgf.cm2 , 13.5-17.8 psi) | ||
| Minimum Standard Value (Used Cap) | 78.5 kPa (0.8 kgf.cm2 , 11.4 psi) | ||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Mechanical | |||
| (1UR-FSE) | |||
| Compression | SERVICE DATA | ||
| Oil Pressure | At Idle: 70 kPa (0.7 kgf.cm2' , 10.1 psi) or more. At 2,500 RPM: 220 kPa (2.2 kgf*cm2, , 31.9 psi) or more. |
||
| Overhaul | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. | ||
| Flywheel/Flex Plate (Drive Plate) Torque | Step 1) 30 N.m (306 kgf.cm, 22 ft.lbs) Step 2) An Additional 90° Turn |
||
| Fuel System | |||
| Pressure Specification | 196 to 588 kPa (2 to 6 kgf/cm2 , 28 to 85 psi) | ||
| Fuel Pressure Test Procedure | ON-VEHICLE INSPECTION | ||
| Fuel Filter Location | In Tank Type COMPONENTS |
||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 1UR-FSE | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Spark Plug (Type = DENSO FK20HBR11) | |||
| Gap | 1.0 to 1.1 mm (0.039 to 0.043 in.) | ||
| Torque | 25 N.m (250 kgf.cm, 18 ft.lbs) | ||
| Starting | |||
| Starter | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Front & Rear | |||
| Adjustment Specifications | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 140 N.m (1428 kgf.cm, 103 ft.lbs) | ||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.