Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSKIA2021FORTE GT, AUTOMATIC DCT TRANSREPAIR AND DIAGNOSIS (SINGLE PAGE)BRAKESANTI-LOCK BRAKESELECTRONIC STABILITY CONTROL DIAGNOSIS
2021 Kia Forte GT, Automatic DCT Trans
Electronic Stability Control Diagnosis
2021 Kia Forte GT, Automatic DCT TransSECTION Electronic Stability Control Diagnosis
- DTC Index
- DTC C1101-01: Battery Voltage High
- DTC C1102-01: Battery Voltage Low
- DTC C1200-01: Wheel Speed Sensor Front-LH Open/Short
- DTC C1201-02: Wheel Speed Sensor Front-LH Range/Performance/Intermittent
- DTC C1202-02: Wheel Speed Sensor Front-LH Invalid/No Signal
- DTC C1203-01: Wheel Speed Sensor Front-RH Open/Short
- DTC C1204-02: Wheel Speed Sensor Front-RH Range/Performance/Intermittent
- DTC C1205-02: Wheel Speed Sensor Front-RH Invalid/No Signal
- DTC C1206-01: Wheel Speed Sensor Rear-LH Open/Short
- DTC C1207-02: Wheel Speed Sensor Rear-LH Range/Performance/Intermittent
- DTC C1208-02: Wheel Speed Sensor Rear-LH Invalid/No Signal
- DTC C1209-01: Wheel Speed Sensor Rear-RH Open/Short
- DTC C1210-02: Wheel Speed Sensor Rear-RH Range/Performance/Intermittent
- DTC C1211-02: Wheel Speed Sensor Rear-RH Invalid/No Signal
- DTC C1235-01: Pressure Sensor (Primary) - Electrical
- DTC C1237-02: Pressure Sensor - Other
- DTC C1260-02: Steering Angle Sensor Circuit 342200223 Signal
- DTC C1261-04: Steering Angle Sensor Is Not Calibrated
- DTC C1283-02: Lateral G Sensor/Longitudinal G Sensor/Yaw Rate Sensor - Signal Error
- DTC C1285-04: Uncalibrated Ax Signal
- DTC C1286-01: Uncalibrated Ax Signal
- DTC C1503-01: TCS Switch Error
- DTC C1542-01: Brake Circuit Error
- DTC C1604-04: ECU Hardware Error
- DTC C1611-08: CAN Time-Out EMS
- DTC C1612-08: CAN Time-Out TCU
- DTC C1613-08: CAN Signal Error EMS
- DTC C1616-08: C-CAN Bus OFF
- DTC C1620-08: 1st Set-Up Not Completed
- DTC C1623-08: CAN Time-Out Steering Angle Sensor
- DTC C1626-04: Implausible Control
- DTC C1638-08: SCC Communication Error
- DTC C1643-08: CAN Time-Out Yaw Rate & G Sensor
- DTC C1649-08: CAN Time-Out EMS for ACC/SCC
- DTC C1650-08: CAN Signal Error ACC
- DTC C1656-08: CAN Signal Error - Cluster
- DTC C1680-01: VSM EBS Error
- DTC C1687-08: CAN Time-Out VSM2 (MDPS)
- DTC C1688-08: VSM2 (MDPS) Signal Error
- DTC C1702-04: Variant Coding Error
- DTC C1734-17: Overvoltage Detected
- DTC C1807-08: Sub CAN Bus OFF
- DTC C1812-08: CAN Time-Out Gateway
- DTC C2112-02: Valve Relay Error
- DTC C2227-01: Excessive Temperature Of Brake Disc
- DTC C2380-01: ABS/TCS/ESP Valve Error
- DTC C2402-01: Motor Electrical
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.