Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Kia Rondo BaseFACTORY OEM SERVICE PROCEDURE
Abs (Anti-Lock Brake System)
- Components
- Description
- Abs Control
- Abs Circuit Diagram
- Abs Connector Input/Output
- Scan Tool Check
- Troubleshooting
- Problem Symptoms Table
- Notes
- ABS Does Not Operate
- ABS Does Not Operate (Intermittently)
- Communication with Scan-Tool is not possible.; (Communication with any system is not possible)
- Communication with Scan Tool is not possible.; (Communication with ABS only is not possible)
- When Ignition Key Is Turned ON (engine OFF), The ABS Warning Lamp Does Not Light Up
- Even After The Engine Is Started, The ABS Warning Lamp Remains ON
- Bleeding Brake System
- Diagnostic Trouble Code Chart (DTC)
- DTC C1101 Battery Voltage High
- DTC C1102 Battery Voltage Low
- DTC C1112 Sensor Power Voltage
- DTC C1200 Wheel Speed Sensor Front-LH Open/Short; DTC C1203 Wheel Speed Sensor Front-RH Open/Short; DTC C1206 Wheel Speed Sensor Rear-LH Open/Short; DTC C1209 Wheel Speed Sensor Rear-RH Open/Short
- DTC C1201 Wheel Speed Sensor Front-LH Range / Performance / Intermittent; DTC C1204 Wheel Speed Sensor Front-RH Range / Performance / Intermittent; DTC C1207 Wheel Speed Sensor Rear-LH Range / Performance / Intermittent; DTC C1210 Wheel Speed Sensor Rear-RH Range / Performance / Intermittent
- DTC C1202 Wheel Speed Sensor Front-LH Invalid/No Signal; DTC C1205 Wheel Speed Sensor Front-RH Invalid/No Signal; DTC C1208 Wheel Speed Sensor Rear-LH Invalid/No Signal; DTC C1211 Wheel Speed Sensor Rear-RH Invalid/No Signal
- DTC C1235 Pressure Sensor (Primary) - Electrical
- DTC C1237 Pressure Sensor - Other
- DTC C1259 Steering Angle Sensor - Electrical
- DTC C1260 Steering Angle Sensor - Signal
- DTC C1282 Yaw Rate And Lateral G Sensor - Electrical
- DTC C1283 Yaw Rate And Lateral G Sensor - Signal
- DTC C1503 ESC Switch Error
- DTC C1513 Brake Switch Error
- DTC C1604 Ecu Hardware Error
- DTC C1605 Can Hardware Error
- DTC C1611 Can Time-Out Ems
- DTC C1612 Can Time-Out TCU
- DTC C1613 Can Wrong Message
- DTC C1616 Can Bus Off
- Component Location
- General Description
- DTC Description
- DTC Detecting Condition
- Terminal And Connector Inspection
- Signal Circuit Inspection
- Can Bus Short (To Ground) Inspection
- Can Bus Short (To Battery) Inspection
- Can Bus Short (Between High And Low) Inspection
- Component Inspection
- Verification Of Vehicle Repair
- DTC C2112 Valve Relay Error
- DTC C2227 Excessive Temperature Of Brake Disc
- DTC C2380 Abs/TCS/ESC Valve Error
- DTC C2402 Motor - Electrical
- Anti-Lock Braking System Control Module
- Front Wheel Speed Sensor
- Rear Wheel Speed Sensor
- EBD (Electronic Brake-Force Distribution)
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.