Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Kia Rondo BaseFACTORY OEM SERVICE PROCEDURE
Diagnostic Trouble Code Chart (DTC)
DIAGNOSTIC TROUBLE CODE CHART
| DTC | Trouble description | Warning lamp | Remarks | ||
|---|---|---|---|---|---|
| EBD | ABS | ESC | |||
| C1101 | Battery voltage high | ◦ | ◦ | ◦ | |
| C1102 | Battery voltage low | X/◦ | ◦ | ◦ | |
| C1112 | Sensor power voltage | X | X | ◦ | ESC |
| C1200 | Wheel speed sensor front-LH open/short | X/◦ | ◦ | ◦ | |
| C1201 | Wheel speed sensor front-LH range / performance / intermittent | X/◦ | ◦ | ◦ | |
| C1202 | Wheel speed sensor front-LH invalid/no signal | X/◦ | ◦ | ◦ | |
| C1203 | Wheel speed sensor front-RH open/short | X/◦ | ◦ | ◦ | |
| C1204 | Wheel speed sensor front-RH range / performance / intermittent | X/◦ | ◦ | ◦ | |
| C1205 | Wheel speed sensor front-RH invalid/no signal | X/◦ | ◦ | ◦ | |
| C1206 | Wheel speed sensor rear-LH open/short | X/◦ | ◦ | ◦ | |
| C1207 | Wheel speed sensor rear-LH range / performance / intermittent | X/◦ | ◦ | ◦ | |
| C1208 | Wheel speed sensor rear-LH invalid/no signal | X/◦ | ◦ | ◦ | |
| C1209 | Wheel speed sensor rear-RH open/short | X/◦ | ◦ | ◦ | |
| C1210 | Wheel speed sensor rear-RH range / performance / intermittent | X/◦ | ◦ | ◦ | |
| C1211 | Wheel speed sensor rear-RH invalid/no signal | X/◦ | ◦ | ◦ | |
| C1235 | Primary pressure sensor - electrical | X | X | ◦ | ESC |
| C1237 | Primary pressure sensor - signal | X | X | ◦ | ESC |
| C1259 | Steering sensor - electrical | X | X | ◦ | ESC |
| C1260 | Steering sensor circuit - signal | X | X | ◦ | ESC |
| C1282 | Yaw rate & lateral G sensor - electrical | X | X | ◦ | ESC |
| C1283 | Yaw rate & lateral G sensor - signal | X | X | ◦ | ESC |
| C1503 | ESC switch error | X | X | ◦ | ESC |
| C1513 | Brake switch error | X | X | ◦ | ESC |
| C1604 | ECU hardware error | ◦ | ◦ | ◦ | |
| C1605 | CAN hardware error | X | X | ◦ | ESC |
| C1611 | CAN time-out EMS | X | X | ◦ | ESC |
| C1612 | CAN time-out TCU | X | X | ◦ | ESC |
| C1613 | CAN wrong message | X | X | ◦ | ESC |
| C1616 | CAN bus off | X | X | ◦ | ESC |
| C2112 | Valve relay error | ◦ | ◦ | ◦ | |
| C2227 | Excessive temperature of brake disc | X | X | ◦ | ESC |
| C2380 | ABS/TCS/ESC valve error | ◦ | ◦ | ◦ | |
| C2402 | Motor electrical | X | ◦ | ◦ | |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
