Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSISUZU2006ASCENDER S, 5.3 M, 4WDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 578 (ENGINE CONTROL SYSTEM & FUEL SYSTEM - 5.3L & 6.0L - INTRODUCTION)
2006 Isuzu Ascender S, 5.3 M, 4WD
Section 578 (Engine Control System & Fuel System - 5.3L & 6.0L - Introduction)
2006 Isuzu Ascender S, 5.3 M, 4WDSECTION Section 578 (Engine Control System & Fuel System - 5.3L & 6.0L - Introduction)
WARNING: This page is about a different car, the 2009 GMC Envoy and 2009 Chevrolet TrailBlazer. However, it is still accessible from the selected car via links, so may be relevant.
- Specifications
- Schematic and Routing Diagrams
- Diagnostic Information and Procedures
- Repair Instructions
- Engine Control Module Replacement
- Crankshaft Position System Variation Learn
- Throttle Learn
- Engine Coolant Temperature Sensor Replacement
- Mass Airflow Sensor with Intake Air Temperature Sensor Replacement
- Manifold Absolute Pressure Sensor Replacement
- Power Brake Booster Vacuum Sensor Replacement (5.3L Only)
- Heated Oxygen Sensor Replacement - Bank 1 Sensor 1
- Heated Oxygen Sensor Replacement - Bank 1 Sensor 2
- Heated Oxygen Sensor Replacement - Bank 2 Sensor 1
- Heated Oxygen Sensor Replacement - Bank 2 Sensor 2
- Accelerator Pedal Position Sensor Replacement
- Throttle Body Assembly Replacement
- Throttle Body Cleaning
- Fuel Pressure Gage Installation and Removal
- Fuel Pressure Relief (With CH-48027)
- Fuel Pressure Relief (Without CH-48027)
- Metal Collar Quick Connect Fitting Service
- Plastic Collar Quick Connect Fitting Service
- Fuel Tank Draining
- Fuel Tank Replacement
- Fuel Tank Pressure Sensor Replacement
- Fuel Level Sensor Replacement
- Fuel Sender Assembly Replacement
- Fuel Hose/Pipes Replacement - Chassis
- Fuel System Cleaning
- Fuel Injection Fuel Rail Assembly Replacement
- Fuel Injector Replacement
- Fuel Injector Cleaning
- Evaporative Emission Canister Purge Solenoid Valve Replacement
- Evaporative Emission Canister Vent Solenoid Valve Replacement
- Evaporative Emission Hoses/Pipes Replacement - Engine
- Evaporative Emission Canister Vent Hose/Pipe Replacement
- Evaporative Emission Hose/Pipe Replacement - Chassis
- Evaporative Emission Hoses/Pipes Replacement - Canister/Fuel Tank
- Evaporative Emission Canister Replacement
- Ignition Coil Replacement
- Spark Plug Wire Inspection
- Spark Plug Wire Replacement
- Spark Plug Inspection
- Spark Plug Replacement
- Crankshaft Position Sensor Replacement
- Camshaft Position Sensor Replacement
- Knock Sensor Replacement (Left Side)
- Knock Sensor Replacement (Right Side)
- Air Cleaner Element Replacement
- Air Cleaner Assembly Replacement
- Air Cleaner Resonator Outlet Duct Replacement
- Description and Operation
- Engine Control Module Description
- Malfunction Indicator Lamp (MIL) Operation
- Cylinder Deactivation (Active Fuel Management) System Description
- Valve Lifter Oil Manifold (VLOM) Assembly
- Engine Control Module (ECM)
- Cylinder Deactivation Inhibit Reasons
- Throttle Actuator Control (TAC) System Description
- Fuel System Description
- Fuel System Overview
- Fuel Tanks
- Fuel Fill Pipe
- Fuel Filler Cap
- Fuel Sender Assembly
- Fuel Level Sensor
- Fuel Pump
- Fuel Strainer
- Fuel Filter
- Nylon Fuel Pipes
- Quick-Connect Fittings
- On-Board Refueling Vapor Recovery (ORVR) System
- Fuel Pipe O-Rings
- Fuel Rail Assembly
- Fuel Injectors
- Fuel Pressure Regulator
- Fuel Metering Modes of Operation
- Fuel Trim
- Evaporative Emission Control System Description
- Electronic Ignition (EI) System Description
- Special Tools and Equipment
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.