SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSINFINITI2019Q70 3.7 LUXE, AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT VARIANT/TRIMSECTION 10 (ENGINE CONTROL SYSTEM (5.6L) (DTC/CIRCUIT DIAGNOSIS) (3 OF 9))DTC/CIRCUIT DIAGNOSISDTC P0181: FTT SENSORDTC LOGICDTC CONFIRMATION PROCEDURE
2019 Infiniti Q70 3.7 Luxe, AWD

DTC Confirmation Procedure

2019 Infiniti Q70 3.7 Luxe, AWDSECTION DTC Confirmation Procedure
WARNING: This page is about a different variant/trim than selected.
  1. INSPECTION START 

    Is it necessary to erase permanent DTC?

    YES

    GO TO 7 .

    NO

    GO TO 2 .

  2. PRECONDITIONING 

    If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following procedure before conducting the next test.

    1. Turn ignition switch OFF and wait at least 10 seconds.
    2. Turn ignition switch ON.
    3. Turn ignition switch OFF and wait at least 10 seconds.

    GO TO 3 .

  3. PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A-I 
    1. Turn ignition switch ON and wait at least 10 seconds.
    2. Check 1st trip DTC.

    Is 1st trip DTC detected?

    YES

    Proceed to Diagnosis Procedure .

    NO

    GO TO 4 .

  4. CHECK ENGINE COOLANT TEMPERATURE 

    SYMBOL WITH CONSULT

    1. Select "COOLAN TEMP/S" in "DATA MONITOR" with CONSULT.
    2. Check "COOLAN TEMP/S" value.

    SYMBOL WITH GST

    Follow the procedure "With CONSULT" above.

    "COOLAN TEMP/S" less than 60 deg.C (140 deg.F)?

    YES

    INSPECTION END

    NO

    GO TO 5 .

  5. PERFORM DTC CONFIRMATION PROCEDURE-II 

    SYMBOL WITH CONSULT

    1. Cool engine down until "COOLAN TEMP/S" is less than 60 deg.C (140 deg.F).
    2. Wait at least 10 seconds.
    3. Check 1st trip DTC.

    SYMBOL WITH GST

    Follow the procedure "With CONSULT" above.

    Is 1st trip DTC detected?

    YES

    Proceed to Diagnosis Procedure .

    NO

    GO TO 6 .

  6. PERFORM COMPONENT FUNCTION CHECK (FOR MALFUNCTION B) 

    Perform component function check. Refer to Component Function Check .

    NOTE: Use the component function check to check the overall function of the FTT sensor circuit. During this check, a 1st trip DTC might not be confirmed.

    Is the inspection result normal?

    YES

    INSPECTION END

    NO

    Proceed to Diagnosis Procedure .

  7. PRECONDITIONING 

    If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following procedure before conducting the next test.

    1. Turn ignition switch OFF and wait at least 10 seconds.
    2. Turn ignition switch ON.
    3. Turn ignition switch OFF and wait at least 10 seconds.

    TESTING CONDITION:

    • Before performing the following procedure, do not add fuel.
    • Before performing the following procedure, check that fuel level is between 1/4 and 4/4.
    • Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

    GO TO 8 .

  8. PERFORM DTC CONFIRMATION PROCEDURE B 
    1. Start engine and let it idle for 60 minutes.
    2. Move the vehicle to a cool place.
      NOTE: Cool the vehicle in an environment of ambient air temperature between -10 deg.C (14 deg.F) and 35 deg.C (95 deg.F).
    3. Turn ignition switch OFF and soak the vehicle for 12 hours.
      CAUTION: Never turn ignition switch ON during soaking.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.