Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSHYUNDAI2009SONATA SE, 3.3 FREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT VARIANT/TRIMSECTION 4 (AUTOMATIC TRANSAXLE SYSTEM (A5GF1))
2009 Hyundai Sonata SE, 3.3 F
Section 4 (Automatic Transaxle System (A5GF1))
2009 Hyundai Sonata SE, 3.3 FSECTION Section 4 (Automatic Transaxle System (A5GF1))
WARNING: This page is about a different variant/trim than selected.
- Automatic Transaxle System
- Service Adjustment Procedure
- Troubleshooting
- P0707 Transmission Range Sensor Circuit Low Input
- P0708 Transmission Range Sensor Circuit High Input
- P0711 Transmission Fluid Temperature Sensor "A" Circuit Range/Performance
- P0712 Transmission Fluid Temperature Sensor "A" Circuit Low Input
- P0713 Transmission Fluid Temperature Sensor "A" Circuit High Input
- P0717 Input/Turbine Speed Sensor "A" Circuit No Signal
- Component Location
- General Description
- DTC Description
- DTC Detecting Condition
- Specification
- Signal Waveform & Data
- Monitor Scantool Data
- Terminal and Connector Inspection
- Signal Circuit Inspection
- Power Circuit Inspection
- Ground Circuit Inspection
- Component Inspection
- Check PCM/TCM
- Verification Of Vehicle Repair
- P0721 Output Speed Sensor Circuit Range/Performance
- Component Location
- General Description
- DTC Description
- DTC Detecting Condition
- Specification
- Signal Waveform & Data
- Monitor Scantool Data
- Terminal and Connector Inspection
- Signal Circuit Inspection
- Power Circuit Inspection
- Ground Circuit Inspection
- Component Inspection
- Check PCM/TCM
- Verification Of Vehicle Repair
- P0722 Output Speed Sensor Circuit No Signal
- P0731 Gear 1 Incorrect Ratio
- P0732 Gear 2 Incorrect Ratio
- P0733 Gear 3 Incorrect Ratio
- P0734 Gear 4 Incorrect Ratio
- P0741 Torque Converter Clutch Circuit Performance or Stuck Off
- P0743 Torque Converter Clutch Circuit Electrical
- P0750 Shift Control Solenoid Valve "A" (Low & Reverse Brake Solenoid)
- P0755 Shift Control Solenoid Valve "B" (Under Drive Clutch Solenoid)
- P0760 Shift Control Solenoid Valve "C" (2nd Brake Solenoid)
- P0765 Shift Control Solenoid Valve "D" (Over Drive Clutch Solenoid)
- P0770 Shift Control Solenoid Valve "E" (Reduction Clutch Solenoid)
- P0880 TCM Power Signal Error Open/Short (GND)
- U0001 High Speed CAN Communication Bus off
- U0100 Lost Communication With ECM/PCM "A"
- Automatic Transaxle
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.