Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSHYUNDAI2003TIBURON BASE, AUTOMATICREPAIR AND DIAGNOSIS (SINGLE PAGE)TRANSMISSIONAUTOMATIC TRANSAXLE SYSTEM
2003 Hyundai Tiburon Base, Automatic
Automatic Transaxle System
2003 Hyundai Tiburon Base, AutomaticSECTION Automatic Transaxle System
- General
- Specifications
- Special Tools
- Troubleshooting (A/T) (F4A42 Model)
- Snap Ring For Adjustment & Spacer (A/T)
- Basic Inspection Adjustment
- Automatic Transaxle Fluid Check
- Automatic Transaxle Fluid
- Transaxle Range Switch Continuity Check
- Transaxle Range Switch & Control Cable Adjustment
- A/T Control Component Check
- Torque Converter Stall Test
- Torque Converter Stall Test Judgement Results
- Hydraulic Pressure Test
- Standard Hydraulic Pressure Test
- Hydraulic Pressure Test Diagnosis Table
- Diagnosis Function
- Road Test
- Diagnostic Trouble Code Description
- Diagnostic Trouble Code Identification
- Inspection Chart For Diagnosis Codes
- Inspection Chart For Trouble Symptoms
- Elements In Use In Each Gear
- Operating Elements & Their Function
- Inspection Process For Diagnostic
- DTC P1702-P1704: Throttle Position Sensor System
- DTC P0712 & P0713: Oil Temperature Sensor System
- DTC P0725: Crankshaft Position Sensor System
- DTC P0715: Input Shaft Speed Sensor System
- DTC P0720: Output Shaft Sensor System
- DTC P0703: Stop Light Switch System
- DTC P0750, P0755, P0760 & P0765: Solenoid Valve System
- DTC P0740 & P0743: Torque Converter Clutch Solenoid System
- DTC P0731: 1st Gear Incorrect Ratio
- DTC P0732: 2nd Gear Incorrect Ratio
- DTC P0733: 3rd Gear Incorrect Ratio
- DTC P0734: 4th Gear Incorrect Ratio
- DTC P0736: Reverse Gear Incorrect Ratio
- DTC P1723: A/T Control Relay System
- Inspection Process For Trouble Symptoms
- Inspection Procedure 1
- Inspection Procedure 2
- Inspection Procedure 3
- Inspection Procedure 4
- Inspection Procedure 5
- Inspection Procedure 6
- Inspection Procedure 7
- Inspection Procedure 8
- Inspection Procedure 9
- Inspection Procedure 10
- Inspection Procedure 11
- Inspection Procedure 12
- Inspection Procedure 13
- Inspection Procedure 14
- Inspection Procedure 15
- Service Adjustment Procedure
- Automatic Transaxle Hydraulic Circuit
- TCM Circuit Diagram (2.0L & 2.7L)
- Automatic Transaxle
- Automatic Transaxle Shift Control
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.