Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Diagnostic Trouble Code (DTC) Chart
2021 Ford Edge SE, 4WDSECTION Diagnostic Trouble Code (DTC) Chart
WARNING: This page is about a different car, the 2021 Ford F-150. However, it is still accessible from the selected car via links, so may be relevant.
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
Diagnostic Trouble Code Chart
| Module | DTC | Description | Action |
|---|---|---|---|
| BCM | B10AB:00 | Remote Keyless Entry Synchronization: No Sub Type Information | GO to Pinpoint Test O |
| BCM | B10C7:01 | Interior Trunk Antenna: General Electrical Failure | GO to Pinpoint Test T |
| BCM | B1218:00 | Transmitter Identification Code: No Sub Type Information | GO to Pinpoint Test O |
| BCM | B121A:11 | Keypad Illumination Output: Circuit Short To Ground | GO to Pinpoint Test AK |
| BCM | B121A:15 | Keypad Illumination Output: Circuit Short To Battery Or Open | GO to Pinpoint Test AK |
| BCM | B121B:01 | Keypad Input Switch: General Electrical Failure | GO to Pinpoint Test N |
| BCM | B12EE:11 | Liftgate/Tailgate/Trunk Release: Circuit Short To Ground | GO to Pinpoint Test M |
| BCM | B12EE:12 | Liftgate/Tailgate/Trunk Release: Circuit Short To Battery | GO to Pinpoint Test M |
| BCM | B12EE:13 | Liftgate/Tailgate/Trunk Release: Circuit Open | GO to Pinpoint Test M |
| BCM | B12EE:15 | Liftgate/Tailgate/Trunk Release: Circuit Short To Battery or Open | GO to Pinpoint Test M |
| BCM | B1336:01 | Left Front Door External Antenna: General Electrical Failure | GO to Pinpoint Test S |
| BCM | B1337:01 | Right Front Door External Antenna: General Electrical Failure | GO to Pinpoint Test S |
| BCM | B1381:11 | Left Front Door Handle Proximity Sensor: Circuit Short to Ground | GO to Pinpoint Test S |
| BCM | B1381:15 | Left Front Door Handle Proximity Sensor: Circuit Short to Battery or Open | GO to Pinpoint Test S |
| BCM | B1381:29 | Left Front Door Handle Proximity Sensor: Signal Invalid | GO to Pinpoint Test S |
| BCM | B1382:11 | Right Front Door Handle Proximity Sensor: Circuit Short to Ground | GO to Pinpoint Test S |
| BCM | B1382:15 | Right Front Door Handle Proximity Sensor: Circuit Short to Battery or Open | GO to Pinpoint Test S |
| BCM | B1382:29 | Right Front Door Handle Proximity Sensor: Signal Invalid | GO to Pinpoint Test S |
| BCM | B14E9:01 | Liftgate Unlock Switch: General Electrical Failure | GO to Pinpoint Test M |
| BCM | B1585:11 | Central Lock Output: Circuit Short To Ground | GO to Pinpoint Test J |
| BCM | B1585:12 | Central Lock Output: Circuit Short To Battery | GO to Pinpoint Test J |
| BCM | B1585:13 | Central Lock Output: Circuit Open | GO to Pinpoint Test J |
| BCM | B1586:11 | Central Unlock Output: Circuit Short To Ground | GO to Pinpoint Test J |
| BCM | B1586:12 | Central Unlock Output: Circuit Short To Battery | GO to Pinpoint Test J |
| BCM | B1586:13 | Central Unlock Output: Circuit Open | GO to Pinpoint Test J |
| BCM | B1587:11 | Driver Door Unlock Output: Short to Ground | GO to Pinpoint Test J |
| BCM | B1587:12 | Driver Door Unlock Output: Short to battery | GO to Pinpoint Test J |
| BCM | B1587:13 | Driver Door Unlock Output: Circuit Open | GO to Pinpoint Test J |
| BCM | B15D5:12 | Passenger Door Unlock Output: Short to Battery | GO to Pinpoint Test J |
| BCM | U0258:87 | Lost Communication With Radio Transceiver: Missing Message | GO to Pinpoint Test U |
| DDM | B108F:23 | Cabin Lock/Unlock Switch: Signal Stuck Low | GO to Pinpoint Test K |
| DDM | U0140:00 | Lost Communication With Body Control Module: No Sub-Type Information | GO to Pinpoint Test V |
| DDM | U0164:00 | Lost Communication With HVAC Control Module: No Sub-Type Information | GO to Pinpoint Test AA |
| DDM | U0208:00 | Lost Communication With "Seat Control Module A": No Sub-Type Information | GO to Pinpoint Test W |
| DDM | U0232:00 | Lost Communication With Side Obstacle Detection Control Module A: No Sub-Type Information | GO to Pinpoint Test X |
| DDM | U0233:00 | Lost Communication With Side Obstacle Detection Control Module - B: No Sub-Type Information | GO to Pinpoint Test Y |
| DDM | U0294:00 | Lost Communication With Powertrain Control Monitor Module: No Sub-Type Information | GO to Pinpoint Test AB |
| DDM | U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test AC |
| DDM | U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test AG |
| DDM | U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test AG |
| DDM | U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AE |
| DDM | U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AF |
| PCM | P04B5:00 | Fuel Fill Door Stuck Open: No Sub-Type Information | GO to Pinpoint Test AJ |
| PCM | P04BA:00 | Fuel Fill Door Position Sensor/Switch Circuit High: No Sub-Type Information | GO to Pinpoint Test AJ |
| PCM | P04C1:00 | Fuel Fill Door Unlock Control Circuit Low: No Sub-Type Information | GO to Pinpoint Test AI |
| PCM | P04C2:00 | Fuel Fill Door Unlock Control Circuit High: No Sub-Type Information | GO to Pinpoint Test AH |
| PCM | P04C9:00 | Fuel Fill Door Open Request Sensor/Switch Performance/Stuck Off: No Sub-Type Information | GO to Pinpoint Test AH |
| PCM | P04CA:00 | Fuel Fill Door Open Request Sensor/Switch Stuck Low: No Sub-Type Information | GO to Pinpoint Test AH |
| PCM | P04CB:00 | Fuel Fill Door Open Request Sensor/Switch Stuck High: No Sub-Type Information | GO to Pinpoint Test AH |
| PCM | P04CD:00 | Fuel Fill Door Open Request Sensor/Switch Stuck On: No Sub-Type Information | GO to Pinpoint Test AH |
| PCM | P1594:00 | Forced Engine Shutdown: Remote Start Fault, No Unattended Vehicle Timeout | GO to Pinpoint Test Z |
| PCM | P1595:00 | Forced Engine Shutdown: Remote Start System Fault, Transmissiom Range Not In Park Position | GO to Pinpoint Test Z |
| PDM | B108F:23 | Cabin Lock/Unlock Switch: Signal Stuck Low | GO to Pinpoint Test K |
| PDM | U0140:00 | Lost Communication With Body Control Module: No Sub-Type Information | GO to Pinpoint Test V |
| PDM | U0164:00 | Lost Communication With HVAC Control Module: No Sub-Type Information | GO to Pinpoint Test AA |
| PDM | U0208:00 | Lost Communication With "Seat Control Module A": No Sub-Type Information | GO to Pinpoint Test W |
| PDM | U0232:00 | Lost Communication With Side Obstacle Detection Control Module A: No Sub-Type Information | GO to Pinpoint Test X |
| PDM | U0233:00 | Lost Communication With Side Obstacle Detection Control Module B: No Sub-Type Information | GO to Pinpoint Test Y |
| PDM | U0294:00 | Lost Communication With Powertrain Control Monitor Module: No Sub-Type Information | GO to Pinpoint Test AB |
| PDM | U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test AC |
| PDM | U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test AG |
| PDM | U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test AG |
| PDM | U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AE |
| PDM | U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AF |
| RTM | U1A00:00 | Private Communication Network: No Sub Type Information | GO to Pinpoint Test U |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.