Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2014F-450 SUPER DUTY PLATINUM, RWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 23 (ENGINE MECHANICAL - 6.7L DIESEL)SPECIFICATIONSTORQUE SPECIFICATIONS
2014 Ford F-450 Super Duty Platinum, RWD
Torque Specifications
2014 Ford F-450 Super Duty Platinum, RWDSECTION Torque Specifications
WARNING: This page is about a different car, the 2013 Ford F-550 Super Duty, 2013 Ford F-450 Super Duty, 2013 Ford F-350 Super Duty, and 2013 Ford F-250 Super Duty. However, it is still accessible from the selected car via links, so may be relevant.
| Description | Nm | lb-ft | lb-in | ||
|---|---|---|---|---|---|
| A/C compressor bolts | 25 | 18 | - | ||
| Accessory drive belt idler pulley bracket bolts (non-A/C vehicles) | 25 | 18 | - | ||
| Accessory drive belt idler pulley bolt | 48 | 35 | - | ||
| Accessory drive belt tensioner bolt | 48 | 35 | - | ||
| Air Cleaner (ACL) outlet pipe clamp | 4 | - | 35 | ||
| Block heater | 41 | 30 | - | ||
| Body bolts | 90 | 66 | - | ||
| Camshaft gear bolt(1) | - | - | - | ||
| Camshaft Position (CMP) sensor bolt | 10 | - | 89 | ||
| Camshaft thrust plate bolts | 25 | 18 | - | ||
| Charge Air Cooler (CAC) tube clamp nut | 9 | - | 80 | ||
| CAC bolts | 12 | - | 106 | ||
| Connecting rod cap bolts (1) | - | - | - | ||
| Coolant crossover manifold assembly bolts | 10 | - | 89 | ||
| Coolant inlet connector fitting | 40 | 30 | - | ||
| Cooling fan clutch electrical connector bolt | 25 | 18 | - | ||
| Cooling fan clutch hub nut(1) | - | - | - | ||
| Cooling fan drive assembly bolts | 24 | 18 | - | ||
| Cooling fan stator nuts | 17 | - | 150 | ||
| Cooling fan stator stand offs | 22 | 16 | - | ||
| Crankcase vent oil separator bolts | 10 | - | 89 | ||
| Crankcase vent oil separator stud bolts | 10 | - | 89 | ||
| Crankshaft main bearing cap bolts (1) | - | - | - | ||
| Crankshaft main bearing cap side bolts (1) | - | - | - | ||
| Crankshaft Position (CKP) sensor bolt | 10 | - | 89 | ||
| Crankshaft pulley bolts (1) | - | - | - | ||
| Cylinder head bolts (M8) (1) | - | - | - | ||
| Cylinder head bolts (M12) (1) | - | - | - | ||
| EGR cooler assembly bolts (1) | - | - | - | ||
| EGR valve inlet tube bolts (1) | - | - | - | ||
| EGR bypass outlet tube bolts | 10 | - | 89 | ||
| EGR valve inlet tube bracket bolts (1) | - | - | - | ||
| EGR valve vacuum regulator bolt | 5 | - | 44 | ||
| Engine Coolant Temperature (ECT) sensor | 27 | - | 20 | ||
| Engine front cover bolts (1) | - | - | - | ||
| Engine support insulator cross bolts | 350 | 258 | - | ||
| Engine support insulator nuts - LH | 200 | 148 | - | ||
| Engine support insulator nuts - RH | 115 | 85 | - | ||
| Engine support insulator bracket bolts (1) | - | - | - | ||
| Engine support insulator studs | 80 | 59 | - | ||
| Engine Oil Pressure (EOP) switch | 20 | - | 177 | ||
| Engine Oil Temperature (EOT) sensor | 20 | - | 177 | ||
| Engine rear cover bolts (M6) (1) | - | - | - | ||
| Engine rear cover bolt (M10) (1) | - | - | - | ||
| Engine wire harness bolt | 10 | - | 89 | ||
| Engine wire harness bracket bolt at frame | 25 | 18 | - | ||
| Engine wire harness ground bolt at frame | 25 | 18 | - | ||
| Engine wire harness nuts at upper oil pan | 12 | - | 106 | ||
| Evaporator-to-compressor suction hose fitting nut | 15 | - | 133 | ||
| Exhaust Gas Recirculation Temperature (EGRT) sensor - outlet | 44 | 32 | - | ||
| Exhaust manifold heat shield bolts | 10 | - | 89 | ||
| Exhaust manifold nuts (1) | - | - | - | ||
| Exhaust manifold studs | 13 | - | 115 | ||
| Exhaust manifold flange nuts | 25 | 18 | - | ||
| Exhaust manifold flange studs | 13 | - | 115 | ||
| Exhaust Pressure (EP) sensor mounting nut (1) | - | - | - | ||
| EP sensor tube nut (1) | - | - | - | ||
| Flexplate mounting bolts (1) | - | - | - | ||
| Front End Accessory Drive (FEAD) mounting bolts | 24 | 18 | - | ||
| Fuel injector hold-down bolts (1) | - | - | - | ||
| Fuel injector supply tubes (1) | - | - | - | ||
| Fuel injection pump supply tube bolt and stud bolt | 10 | - | 89 | ||
| Fuel rail bolts (1) | - | - | - | ||
| Fuel rail supply tube bracket bolts | 10 | - | 89 | ||
| Fuel supply tube assembly bolt and stud bolt(1) | - | - | - | ||
| Fuel supply tube assembly connector (1) | - | - | - | ||
| Generator B+ terminal nut | 17 | - | 150 | ||
| Generator mounting bolt | 48 | 35 | - | ||
| Glow plug | 11 | - | 97 | ||
| Ground strap bolt | 10 | - | 89 | ||
| Heater supply tube bolts | 10 | - | 89 | ||
| High-pressure fuel injection pump drive gear nut | 80 | 59 | - | ||
| High-pressure fuel injection pump mounting bolts | 48 | 35 | - | ||
| High-pressure fuel injection pump spacers | 24 | 18 | - | ||
| High-pressure fuel injection pump supply tube retainer nut | 11 | - | 97 | ||
| LH battery tray bolts | 18 | - | 159 | ||
| Lower engine wire harness bolts | 12 | - | 108 | ||
| Lower engine wire harness nuts | 12 | - | 108 | ||
| Lower intake manifold bolts | 24 | 18 | - | ||
| Manifold Absolute Pressure (MAP) sensor | 5 | - | 44 | ||
| Oil cooler bolts (1) | - | - | - | ||
| Oil cooler nut (1) | - | - | - | ||
| Oil filter adapter bolts | 10 | - | 89 | ||
| Oil filter adapter stud bolt | 10 | - | 89 | ||
| Oil level indicator tube bolt | 10 | - | 89 | ||
| Oil fill pipe bolt | 10 | - | 89 | ||
| Oil pan baffle bolts(1) | - | - | - | ||
| Oil pan bolts - lower (1) | - | - | - | ||
| Oil pan bolts - upper(1) | - | - | - | ||
| Oil pan drain plug | 26 | 19 | - | ||
| Oil pump screen and pick-up tube bolts | 10 | - | 89 | ||
| Oil spray bar nuts (1) | - | - | - | ||
| PCM nuts | 7 | - | 62 | ||
| Piston cooling tube bolts | 10 | - | 89 | ||
| Positive battery cable clamp nut | 7 | - | 62 | ||
| Positive power distribution cable nut | 9 | - | 80 | ||
| Power steering pressure tube bolt | 12 | - | 106 | ||
| Power steering pump bracket bolts | 24 | 18 | - | ||
| Power steering pump bolts | 25 | 18 | - | ||
| Primary coolant pump bolts | 10 | - | 89 | ||
| Rocker arm assembly bolts (1) | - | - | - | ||
| Secondary fuel filter assembly bolts | 10 | - | 89 | ||
| Secondary coolant pump mounting bolts | 25 | 18 | - | ||
| Starter harness ground bolt | 25 | 18 | - | ||
| Starter harness retainer bracket nut | 12 | - | 106 | ||
| Starter mounting bolts (1) | - | - | - | ||
| Starter positive cable nut | 12 | - | 106 | ||
| Starter solenoid wire nut | 5 | - | 44 | ||
| Thermostat housing bolts | 10 | - | 89 | ||
| Throttle body bolts | 10 | - | 89 | ||
| Torque converter nuts | 55 | 41 | - | ||
| Transmission cooler tubes nut at engine | 12 | - | 106 | ||
| Transmission cooler tubes bracket nut | 9 | - | 80 | ||
| Transmission fluid indicator tube bolt at engine | 11 | - | 97 | ||
| Transmission fluid indicator tube nut at transmission | 25 | 18 | - | ||
| Transmission support insulator nuts | 115 | 85 | - | ||
| Transmission shift cable bracket bolt | 48 | 35 | - | ||
| Transmission-to-engine bolts | 48 | 35 | - | ||
| Turbocharger downpipe bracket bolt | 25 | 18 | - | ||
| Turbocharger downpipe clamp nut at turbocharger | 15 | - | 133 | ||
| Turbocharger downpipe clamp nut at pipe | 55 | 41 | - | ||
| Turbocharger downpipe flange bolt | 40 | 30 | - | ||
| Turbocharger heat shield bolts | 10 | - | 89 | ||
| Turbocharger inlet pipe clamp nut at turbine | 15 | - | 133 | ||
| Turbocharger inlet pipe nut at exhaust manifold | 25 | 18 | - | ||
| Turbocharger mounting bolts (1) | - | - | - | ||
| Upper oil pan plug | 102 | 75 | - | ||
| Upper intake manifold bolts (1) | - | - | - | ||
| Vacuum pump bolts | 10 | - | 89 | ||
| Valve cover bolts (1) | - | - | - | ||
| Valve cover stud bolts (1) | - | - | - | ||
| 3/4 x 14 M cylinder block plug (HP oil) (1) | - | - | - | ||
| 1/2 x 14 M cylinder block upper plug (HP oil) (1) | - | - | - | ||
| 1/2 x 14 M cylinder block lower plug (water jacket drains) | 40 | 30 | - | ||
| M 27 x 2 x 6 cylinder block plug | 72 | 53 | - | ||
|
|||||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.