Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHRYSLER2008SEBRING CONVERTIBLE V6-2.7LREPAIR AND DIAGNOSISTRANSMISSION AND DRIVETRAINTECHNICAL SERVICE BULLETINSALL TECHNICAL SERVICE BULLETINSRECALL - TIPM REFLASH FOR A/T SHIFT CONCERNSSERVICE PROCEDUREB. REPROGRAM THE TIPM MODULE USING STARMOBILE
2008 Chrysler Sebring Convertible V6-2.7L
B. Reprogram the TIPM Module Using StarMOBILE
2008 Chrysler Sebring Convertible V6-2.7LSECTION B. Reprogram the TIPM Module Using StarMOBILE
1. Open the hood and install a battery charger. Verify that the charging rate provides approximately 13.0 to 13.5 volts. Do not allow the charger to time out during the flash process. Set the battery charger timer (if so equipped) to continuous charge.
NOTE:
Use an accurate stand alone voltmeter. The battery charger volt meter may not be sufficiently accurate. Voltages outside of the specified range will cause an unsuccessful flash. If voltage reading is too high, apply an electrical load by activating the park or headlamps and/or HVAC blower motor to lower the voltage.
2. Connect the StarMOBILE scan tool to the vehicle data link connector located under the steering column and turn the ignition key to the "RUN" position.
3. Power ON the StarMOBILE scan tool.
4. Connect the CH9410 StarMOBILE scan tool ethernet cable to the StarMOBILE and the dealer's network drop.
5. From the desktop, launch the "StarMOBILE Desktop Client" software.
6. Establish a connection with the StarMOBILE scan tool.
7. Select "Flash Download".
8. Select "Next" and then enter your ID and password.
9. Enter the vehicle information (manually or use the automatic function).
10. Highlight the required flash file and select "Download to Client".
11. Select "BACK" then select "ECU View".
12. Select "TIPMCGW".
13. Select "More Options".
14. Select "ECU Flash".
15. Select "Manage Files".
16. Highlight downloaded flash file.
17. Select "Copy to SM Device" and then follow the screen prompts.
18. Disconnect the ethernet cable from the StarMOBILE scan tool.
19. Turn off the StarMOBILE scan tool and then restart the scan tool.
NOTE:
The StarMOBILE scan tool must be shut down and restarted to unlock the flash.
20. From the "System Status" screen press the "Exit" button.
21. From the "Main Menu" select "Enter Standalone Diagnostic Mode" and press the select button.
22. Select "ECU View" and press the select button.
23. Highlight "TIPMCGW" and press the select button.
24. Select "FLASH ECU" and press the select button.
25. Compare the highlighted software part number with the software part number displayed at the top of the screen.
> If the part numbers are the same, the module is up to date and reprogramming is not required. Continue to Step 28.
> If the software part numbers are different, press the select button to reprogram the module.
26. Verify the file number on the screen. If correct press the select button and follow the screen prompts.
27. When the flash is complete, press the "OK" button.
28. Clear any Diagnostic Trouble Codes (DTCs) as follows:
NOTE:
Due to the TIPM programming procedure, DTC(s) may be set in other modules (PCM, TCM, ABS, BCM, MIC, WCM, etc.) within the vehicle, if so equipped. Some DTC's may cause the MIL to illuminate.
a. From the "Standalone Home" screen highlight "All DTC's and then press the select button.
b. Highlight "Clear All Stored" and then press the select button.
c. Follow the screen prompts on the StarMOBILE screen.
29. Turn the ignition key to the "OFF" position and remove the StarMOBILE unit, StarMOBILE cable, and battery charger from the vehicle.
NOTE:
Use an accurate stand alone voltmeter. The battery charger volt meter may not be sufficiently accurate. Voltages outside of the specified range will cause an unsuccessful flash. If voltage reading is too high, apply an electrical load by activating the park or headlamps and/or HVAC blower motor to lower the voltage.
2. Connect the StarMOBILE scan tool to the vehicle data link connector located under the steering column and turn the ignition key to the "RUN" position.
3. Power ON the StarMOBILE scan tool.
4. Connect the CH9410 StarMOBILE scan tool ethernet cable to the StarMOBILE and the dealer's network drop.
5. From the desktop, launch the "StarMOBILE Desktop Client" software.
6. Establish a connection with the StarMOBILE scan tool.
7. Select "Flash Download".
8. Select "Next" and then enter your ID and password.
9. Enter the vehicle information (manually or use the automatic function).
10. Highlight the required flash file and select "Download to Client".
11. Select "BACK" then select "ECU View".
12. Select "TIPMCGW".
13. Select "More Options".
14. Select "ECU Flash".
15. Select "Manage Files".
16. Highlight downloaded flash file.
17. Select "Copy to SM Device" and then follow the screen prompts.
18. Disconnect the ethernet cable from the StarMOBILE scan tool.
19. Turn off the StarMOBILE scan tool and then restart the scan tool.
NOTE:
The StarMOBILE scan tool must be shut down and restarted to unlock the flash.
20. From the "System Status" screen press the "Exit" button.
21. From the "Main Menu" select "Enter Standalone Diagnostic Mode" and press the select button.
22. Select "ECU View" and press the select button.
23. Highlight "TIPMCGW" and press the select button.
24. Select "FLASH ECU" and press the select button.
25. Compare the highlighted software part number with the software part number displayed at the top of the screen.
> If the part numbers are the same, the module is up to date and reprogramming is not required. Continue to Step 28.
> If the software part numbers are different, press the select button to reprogram the module.
26. Verify the file number on the screen. If correct press the select button and follow the screen prompts.
27. When the flash is complete, press the "OK" button.
28. Clear any Diagnostic Trouble Codes (DTCs) as follows:
NOTE:
Due to the TIPM programming procedure, DTC(s) may be set in other modules (PCM, TCM, ABS, BCM, MIC, WCM, etc.) within the vehicle, if so equipped. Some DTC's may cause the MIL to illuminate.
a. From the "Standalone Home" screen highlight "All DTC's and then press the select button.
b. Highlight "Clear All Stored" and then press the select button.
c. Follow the screen prompts on the StarMOBILE screen.
29. Turn the ignition key to the "OFF" position and remove the StarMOBILE unit, StarMOBILE cable, and battery charger from the vehicle.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.