Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2008HHR LT, 2.4 P, AUTOMATICREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 475 (BATTERY, CHARGING SYSTEM AND STARTING SYSTEM)
2008 Chevrolet HHR LT, 2.4 P, Automatic
Section 475 (Battery, Charging System And Starting System)
2008 Chevrolet HHR LT, 2.4 P, AutomaticSECTION Section 475 (Battery, Charging System And Starting System)
WARNING: This page is about a different car, the 2011 GMC Canyon and 2011 Chevrolet Colorado. However, it is still accessible from the selected car via links, so may be relevant.
- Specifications
- Wiring Schematics
- Diagnostic Information and Procedures
- Diagnostic Code Index
- DTC B1327
- Diagnostic Instructions
- DTC Descriptor
- Diagnostic Fault Information
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Diagnostic Aids
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Repair Procedures
- DTC B1390
- DTC B1420
- Diagnostic Instructions
- DTC Descriptor
- Diagnostic Fault Information
- Typical Scan Tool Data
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Diagnostic Aids
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Repair Procedures
- DTC B1487
- DTC B1488
- DTC B1492
- Diagnostic Instructions
- DTC Descriptor
- Diagnostic Fault Information
- Typical Scan Tool Data
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Repair Procedures
- DTC B1516
- DTC B151B
- DTC B1566
- DTC C0899
- Diagnostic Instructions
- DTC Descriptor
- Diagnostic Fault Information
- Typical Scan Tool Data
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Repair Procedures
- DTC C0900
- Diagnostic Instructions
- DTC Descriptor
- Diagnostic Fault Information
- Typical Scan Tool Data
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Diagnostic Aids
- Reference Information
- Circuit/System Verification
- Repair Procedures
- DTC C0901
- DTC P0562 (ECM)
- Diagnostic Instructions
- DTC Descriptor
- Diagnostic Fault Information
- Typical Scan Tool Data
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Repair Procedures
- DTC P0562 (FSCM)
- DTC P0563 (ECM)
- Diagnostic Instructions
- DTC Descriptor
- Diagnostic Fault Information
- Typical Scan Tool Data
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Reference Information
- Diagnostic Aids
- Circuit/System Verification
- Repair Procedures
- DTC P0563 (FSCM)
- DTC P0615
- Diagnostic Instructions
- DTC Descriptor
- Diagnostic Fault Information
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Component Testing
- Repair Procedures
- DTC P0621
- DTC P0622
- Diagnostic Instructions
- DTC Descriptor
- Diagnostic Fault Information
- Typical Scan Tool Data
- Circuit Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Repair Procedures
- Symptoms - Engine Electrical
- Battery Inspection/Test
- Battery Charging
- Battery Electrical Drain/Parasitic Load Test
- Battery Common Causes of Malfunction
- Charging System Test
- Generator Noise Diagnosis
- Starter Solenoid Does Not Click (Manual MA5)
- Starter Solenoid Does Not Click (Automatic M30)
- Starter Solenoid Clicks, Engine Does Not Crank
- Engine Cranks Slowly
- Starter Noise Diagnosis
- Repair Instructions
- Battery Negative Cable Disconnection and Connection
- Generator Battery Control Module Replacement (4 and 5 Cylinder)
- Generator Battery Control Module Replacement (V8)
- Battery Positive and Negative Cable Replacement (LLV/LLR)
- Battery Negative Cable Replacement (LH9)
- Generator Cable Replacement (LLV/LLR)
- Battery Replacement (LLV/LLR)
- Battery Replacement (LH9)
- Battery Box Replacement
- Starter Replacement (LLV/LLR)
- Starter Replacement (LH9)
- Generator Bracket Replacement (LH9)
- Generator Replacement (LLV/LLR)
- Generator Replacement (LH9)
- Description and Operation
- Battery Description and Operation
- Charging System Description and Operation
- Electrical Power Management Description and Operation
- Load Shed System Description and Operation
- Starting System Description and Operation
- Special Tools and Equipment
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.