SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2008CHEVY EXPRESS G2500, VAN CARGO, 6.6 6REPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 933 (ANTILOCK BRAKE SYSTEM, TRACTION CONTROL SYSTEM & STABILITY CONTROL SYSTEM)REPAIR INSTRUCTIONSWHEEL SPEED SENSOR RING REPLACEMENT - REARINSTALLATION PROCEDURE
2008 Chevrolet Chevy Express G2500, Van Cargo, 6.6 6

Installation Procedure

2008 Chevrolet Chevy Express G2500, Van Cargo, 6.6 6SECTION Installation Procedure
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2007 GMC Yukon XL, 2007 GMC Yukon, 2007 Chevrolet Tahoe, 2007 Chevrolet Suburban, and 2007 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: Installing Wheel Speed Sensor Ring Using J 45860 & J 8092
    GM885621Courtesy of GENERAL MOTORS CORP.
  1. Install the wheel speed sensor ring using the J 45860  (1) and the J 8092  (2). See Special Tools .
  2. Drive the wheel speed sensor ring into the axle housing until the tool bottoms against the tube.
    3. Fig 2: Installing The Axle Shaft Bearing Using J 23690 Or J 29709 & J 8092
    GM695758Courtesy of GENERAL MOTORS CORP.
  3. Install the axle shaft bearing using the J 23690  (1) and the J 8092  (2). See Special Tools .
  4. Drive the axle shaft bearing into the axle housing until the tool bottoms against the tube.
    5. Fig 3: Installing Axle Shaft Seal Using J 21128
    GM885624Courtesy of GENERAL MOTORS CORP.
  5. Install the axle shaft seal using the J 21128  . See Special Tools .
  6. Drive the tool into the bore until the axle shaft seal bottoms flush with the tube.
  7. Install the axle shaft. Refer to Rear Axle Shaft Replacement (8.6, 9.5 LD Axle) or Rear Axle Shaft Replacement (9.5 HD Axle) in Rear Drive Axle.
  8. Install the rear axle housing cover. Refer to Rear Axle Housing Cover and Gasket Replacement in Rear Drive Axle.
  9. Install the rear wheel speed sensor. Refer to Rear Wheel Speed Sensor Replacement .
  10. Install the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  11. Fill the rear axle. Refer to Lubricant Replacement - Rear Drive Axle (8.6 Inch Axle) or Lubricant Replacement - Rear Drive Axle (9.5 Inch LD Axle) or Lubricant Replacement - Rear Drive Axle (9.5 Inch HD Axle) in Rear Drive Axle.
  12. Lower the vehicle.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.