Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DBβ LIVE
HOMESERVICE MANUALSCHEVROLET2006SUBURBAN C2500, 6.0 UREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 289 (SECURITY SYSTEM AND LOCKS SYSTEM)
2006 Chevrolet Suburban C2500, 6.0 U
Section 289 (Security System And Locks System)
2006 Chevrolet Suburban C2500, 6.0 USECTION Section 289 (Security System And Locks System)
WARNING: This page is about a different car, the 2004 Mazda 3. However, it is still accessible from the selected car via links, so may be relevant.
- Security And Locks Location Index
- Front Outer Handle Removal/Installation
- Rear Outer Handle Removal/Installation
- Inner Handle Removal/Installation
- Front Door Key Cylinder Removal/Installation
- Front Door Latch And Lock Actuator Removal/Installation
- Rear Door Latch And Lock Actuator Removal/Installation
- Front Door Latch And Lock Actuator Inspection
- Rear Door Latch And Lock Actuator Inspection
- Front Door Lock Actuator Inspection
- Rear Door Lock Actuator Inspection
- Front Door Latch Switch Inspection
- Rear Door Latch Switch Inspection
- Door Lock-Link Switch Inspection
- Front Door Key Cylinder Switch Inspection
- Door Lock Switch Removal/Installation
- Door Lock Switch Inspection
- Door Lock Striker Removal/Installation
- Fuel-Filler Lid Opener Removal/Installation
- Hood Latch And Release Lever Removal/Installation
- Hood Latch Switch Inspection
- Keyless Control Module Removal/Installation
- Keyless Control Module Inspection
- Transmitter Battery Replacement
- Transmitter Battery Inspection
- Transmitter Id Code Registration
- Trunk Lid Latch Removal/Installation
- Trunk Lid Opener Removal/Installation
- Trunk Lid Latch Switch Inspection
- Trunk Lid Key Cylinder Removal/Installation
- Trunk Lid Key Cylinder Switch Inspection
- Trunk Lid Lock Striker Removal/Installation
- Liftgate Outer Handle Removal/Installation
- Liftgate Latch And Lock Actuator Removal/Installation
- Liftgate Lock Actuator Inspection
- Liftgate Latch Switch Inspection
- Liftgate Lock Striker Removal/Installation
- Coil Antenna Removal/Installation
- Immobilizer System Component Replacement/Key Addition And Clearing
- Foreword
- No. 1 Additional Key Registration Procedure (Using Two Valid Keys)
- No. 2 Additional Key Registration Procedure (Using The WDS Or Equivalent)
- No. 3 Key Replacement Procedure (Clearing Previously Registered Key Id Numbers, Key Re-Registration)
- No. 4 Changing The Method For Registering Additional Keys
- No. 5 Resetting Procedure For The Immobilizer System When Replacing The Pcm Or Instrument Cluster
- No. 6 Security Access Procedure
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.