Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006COBALT SS, 4D SEDAN, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 892 (WIRING SYSTEMS AND POWER MANAGEMENT - COMPONENT CONNECTOR END VIEWS - 1 THROUGH D)COMPONENT CONNECTOR END VIEWS - 1 THROUGH DBODY CONTROL MODULE (BCM) X4
2006 Chevrolet Cobalt SS, 4D Sedan, Standard
Body Control Module (BCM) X4
2006 Chevrolet Cobalt SS, 4D Sedan, StandardSECTION Body Control Module (BCM) X4
WARNING: This page is about a different car, the 2010 Pontiac G5 and 2010 Chevrolet Cobalt. However, it is still accessible from the selected car via links, so may be relevant.
Body Control Module (BCM) X4
| Pin | Wire | Circuit | Function |
|---|---|---|---|
| A1 | 2 RD/WH | 640 | Battery Positive Voltage (UQ3) |
| A2-A12 | - | - | Not Used |
| B1 | 0.35 OG | 228 | Windshield Washer Pump Control |
| B2 | 0.35 GY | 8 | I/P Lamp Supply Voltage |
| B3-B12 | - | - | Not Used |
| C1 | 0.5 RD/WH | 1440 | Battery Positive Voltage |
| 0.5 RD/WH | 1440 | Battery Positive Voltage (UAF) | |
| C2 | 0.35 GY | 8 | I/P Lamp Supply Voltage |
| 0.35 GY | 8 | I/P Lamp Supply Voltage | |
| C3-C5 | - | - | Not Used |
| C6-C7 | - | - | Not Available |
| C8 | 0.35 BN | 4 | Accessory Voltage |
| C9-C10 | - | - | Not Used |
| C11 | 0.35 GY | 8 | I/P Lamp Supply Voltage |
| C12 | 0.35 GY | 8 | I/P Lamp Supply Voltage |
| D1 | 0.35 RD/WH | 1040 | Battery Positive Voltage |
| D2 | - | - | Not Used |
| D3 | 0.35 YE | 5199 | Run/Crank Voltage |
| D4 | 3 BN | 141 | Ignition 3 Voltage |
| D5 | - | - | Not Used |
| D6-D7 | - | - | Not Available |
| D8-D9 | - | - | Not Used |
| D10 | 1 RD/WH | 1140 | Battery Positive Voltage |
| 0.5 RD/WH | 1140 | Battery Positive Voltage (AU0) | |
| D11-D12 | - | - | Not Used |
| E1-E5 | - | - | Not Used |
| E6 | 0.35 PK | 439 | Ignition Voltage |
| 0.35 PK | 439 | Ignition Voltage (LNF without UAF) | |
| E7-E11 | - | - | Not Used |
| E12 | 2 BK | 550 | Ground |
| F1 | 0.35 RD/WH | 1540 | Battery Positive Voltage |
| 0.35 RD/WH | 1540 | Battery Positive Voltage | |
| F2 | 0.35 GY | 8 | I/P Lamp Supply Voltage (LNF) |
| F3 | 0.35 GY | 8 | I/P Lamp Supply Voltage (KA1) |
| 0.35 GY | 8 | I/P Lamp Supply Voltage (KA1) | |
| F4 | 0.35 PK | 339 | Ignition 1 Voltage |
| F5 | 0.5 PK | 339 | Ignition Voltage |
| F6 | 0.5 PK | 339 | Ignition Voltage |
| 0.5 PK | 339 | Ignition Voltage (UAF) | |
| F7-F8 | - | - | Not Used |
| F9 | 0.5 PK | 1539 | Ignition Voltage |
| 0.35 PK | 1539 | Ignition 1 Voltage (K34) | |
| F10-F12 | - | - | Not Used |
Connector Part Information
|
Terminal Part Information
|
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.