SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2006COBALT SS, 4D SEDAN, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 406 (CRUISE CONTROL SYSTEM)DIAGNOSTIC INFORMATION AND PROCEDURESDTC P0567 (2.2L)TEST DESCRIPTION
2006 Chevrolet Cobalt SS, 4D Sedan, Standard

Test Description

2006 Chevrolet Cobalt SS, 4D Sedan, StandardSECTION Test Description
WARNING: This page is about a different car, the 2006 Saturn Vue. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 2:  This step determines if condition is present.
  2. 3:  This step determines if the switch is at fault.
DTC P0567 (2.2L)

Step Action Yes No
Schematic Reference: Cruise Control Schematics 
Connector End View Reference: Cruise Control Connector End Views 
1 Did you perform the Diagnostic System Check - Vehicle? Go to Step 2  Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2 
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Turn the cruise control On/Off switch ON.
  4. With the scan tool, observe the Cruise Resume/Accel parameter in the powertrain control module (PCM) General Info Inputs data list.
Does the Cruise Resume/Accel parameter display On?		 Go to Step 3  Go to Diagnostic Aids
3 
  1. Turn OFF the ignition.
  2. Disconnect the cruise control switch.
  3. Turn ON the ignition, with the engine OFF.
  4. With the scan tool, observe the Cruise Resume/Accel parameter.
Does the Cruise Resume/Accel parameter display On?		 Go to Step 4  Go to Step 5 
4 Test the cruise control resume/accel switch signal circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 9  Go to Step 6 
5 Inspect for poor connections at the harness connector of the cruise control switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 9  Go to Step 7 
6 Inspect for poor connections at the harness connector of the engine control module (ECM). Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 9  Go to Step 8 
7 Replace the cruise control switch. Refer to Steering Wheel Control Switch Assembly Replacement in Steering Wheel and Column.
Did you complete the replacement?		 Go to Step 9  -
8 Replace the ECM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.
Did you complete the replacement?		 Go to Step 9  -
9
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC.
Does the DTC reset?		 Go to Step 2  System OK
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.